User manual SYMPHONIC WF803

[. . . ] OWNER'S MANUAL DVD PLAYER with VIDEO CASSETTE RECORDER WF803 ReWritable Recordable POWER OPEN/CLOSE CHANNEL STOP/EJECT PLAY DVD OUTPUT REC PLAY DISC IN DVD VCR TIMER/REC VCR VIDEO AUDIO STOP SKIP/REV PLAY FWD/SKIP REW F. FWD INSTRUCCIONES EN ESPAÑOL INCLUIDAS. If you need additional assistance for set-up or operating after reading owner's manual, please call TOLL FREE : 1- 800 - 242-7158 or visit our web site at http://www. funai-corp. com Please read before using this equipment. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. [. . . ] Then, press B. ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /12 MON START TIME 07: 30 PM END TIME 08: 30 PM CHANNEL -REC SPEED - - light is on or flashes, or during a timer recording. Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don't have to set the TIMER off to use the DVD only. If you connected the DVD/VCR COMBINATION UNIT to a cable box or satellite box as in "DVD/VCR TO TV CONNECTION" on page 13, select the DVD/VCR to channel 3 or 4 the same channel as RF output channel of the DVD/VCR. Then, select the channel you want to record with the cable box or satellite box. Leave the cable box or satellite box on for timer recording. TO STOP AN AUTOMATIC TIMER PROGRAM ALREADY STARTED Press STOP/EJECT on the DVD /VCR COMBINATION UNIT. TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAM 1 Press T-SET. ¡If the DVD output mode is selected, you have to switch it to the VCR mode by pressing the VCR on the remote control or the OUTPUT on the VCR. 7) Set the tape speed Press K or L repeatedly for the desired tape speed. Then, press B. ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /12 MON START TIME 07: 30 PM END TIME 08: 30 PM 16 CHANNEL REC SPEED SP SP SLP 2 Select main menu by pressing MENU. 5 To set another program, repeat step [4]. To exit, press CLEAR/C. RESET. 3 Select "TIMER PROGRAMMING" by pressing K or L. Then, press B. 6 Press T-SET to set the timer. ¡The TIMER REC light on the DVD/VCR COMBINATION UNIT comes on. TIMER RECORDING WILL NOT BE ACTIVATED UNLESS YOU PRESS T-SET. 4 Select the program number you want to check by pressing K or L. ¡The details of the selected program appears on the TV screen. ¡Go to the digit you want to change by pressing B or HINTS FOR TIMER RECORDING VCR ¡If there is a power failure or the VCR is unplugged s. Then, enter correct numbers by pressing o or p. ¡You may cancel the entire program by pressing s while the program number flashes. 5 Press CLEAR/C. RESET to exit. 6 Press T-SET to return to timer stand-by mode. EN 1L25 for more than 30 seconds, the clock setting and all timer settings will be lost. ­ 20 ­ SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. You can not copy a DVD to a videotape. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See "RF OUTPUT CHANNEL" on page 13 for the detail). Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording VCR] (this unit) DVD/VCR AUDIO OUT 2 Press VCR/TV on the recording VCR. VCR DVD S-VIDEO COMPONENT AUDIO VIDEO OUT OUT OUT Y DIGITAL AUDIO OUT ANT-IN L R ANT-OUT VIDEO OUT AUDIO IN Cb L COAXIAL VIDEO IN Cr R RF cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) OUT IN AUDIO VIDEO ANT in [Playing VCR] (another source) 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with a safety tab into the recording VCR. 3 Press SPEED on the recording VCR to select the desired recording speed (SP/SLP). 4 Select the "L1" or "L2"position on the recording VCR. [. . . ] 2 Presione el botón OPEN/CLOSE para abrir la bandeja de carga para discos. Presione el botón o ó p repetidamente. Entonces, presione B. 3) Ajuste el a o 3 Ponga el disco elegido en la bandeja, con la etiqueta hacía arriba. 4 Presione PLAY. ¡La bandeja se cerrará automáticamente, y empezará Presione el botón o ó p repetidamente. El día de la semana aparecerá automáticamente. 4) Ajuste la hora Presione el botón o ó p repetidamente. Entonces, presione B. 5) Ajuste los minutos la reproducción desde el primer capítulo o pista del disco. [. . . ]