User manual TALLYGENICOM T2340-9

[. . . ] Important Information This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in accordance with the manufacturer's instructions, may cause interference in radio and television reception. It has been type tested and found to comply with the limits for class B computing devices in accordance with the specification in subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a partial installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient the receiving antenna, Relocate the peripheral away from the receiver, Move the peripheral away from the receiver Plug the peripheral into a different outlet, so that the peripheral and receiver are on different branch circuits If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. [. . . ] Please open the printer package and check that all the following items are included. Make sure that the unit is set to the correct voltage (i. If this is not the case, contact your dealer. Never switch on the printer when it is not set to the correct voltage since this could cause severe damage. Connect the power cable to the printer's power inlet as shown in the figure. Connect the power cable plug to a wall outlet. Make sure that the printer and the computer are switched off. Connect the printer-end connector of the data cable to the female interface connector and secure it with the spring clips. The power switch, which is used for switching the printer on and off, is located at the right side of the printer. You can control printer operation using the control panel and the keys. It can receive data from the computer only in this mode. If Load is displayed above this key, no paper is loaded in the printer; press the key to feed paper to the printing position. Tear key: Activates the tear function when fanfold paper is loaded Step feeds, line feeds and form feeds can be performed via the control panel only in this mode (see page 15). Short keypress: Line feed (LF) Long keypress: Form feed (FF) Short keypress: Micro-step return Long keypress: Constant paper feed return Short keypress: Micro-step forward Long keypress: Constant paper feed forward Clears the paper path with paper loaded and activates paper path quick selection (see page 14). If no paper is loaded: Load key (see above). In this mode, the following settings are available: Sets the font and the number of characters per inch (Char menu). Paper path (Paperway menu) Tear position and first printing line (Adjust menu) Other menu settings (Menu) For information on how to enable access to these options as well as about the options available, refer to the online documentation on the CD-ROM, chapter 1, Operation (Unlock the menu mode). The first line of the display informs you about whether the printer is in Online or in Offline mode and about the paper path selected (Trac. Remove any paper loaded into the printer. Before opening the cover, make sure that the printer is switched off. Pull the Latch Levers near the right and left ends on the Access Cover to the front, and detach the entire Access Cover. Move the Print head to approximately the center. [. . . ] The following table shows the adjustable range: Number of Copies/ Thickness of Paper Original only Thin Normal Thick Original + 1 Original + 2 Original + 3 Original + 4 Original + 5 Postal Card Reserved Ream (kg) 45­55 55­77 77­110 34/34 34/34/34 34/34/34/34 34/34/34/34/34 34/34/34/34/34/34 110 -- g/m2 50­65 65­90 90­130 40/40 40/40/40 40/40/40/40 40/40/40/40/40 40/40/40/40/40/40 130 -- Lever Position "Ream" is a unit of paper thickness, indicating the weight in kg, of 1, 000 cut sheets at 788 mm x 1091 mm. When printing the original sheet only, Cut Sheet Paper of 45 kg and thicker or Continuous Form Feed Paper of 50 kg and thicker can be used. When the Paper Thickness Adjustment Lever is set higher than appropriate, the printout will appear scratchy and the print head and ribbon lives will be shortened. Setup mode to single sheet mode When fanfold paper was in use and you want to change over to single sheet mode, proceed as described below. [. . . ]