User manual TANDBERG 220-420LTO QUICK INSTALLATION GUIDE
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TANDBERG 220-420LTO. We hope that this TANDBERG 220-420LTO user guide will be useful to you.
Lastmanuals help download the user guide TANDBERG 220-420LTO.
Manual abstract: user guide TANDBERG 220-420LTOQUICK INSTALLATION GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] Tandberg 220/420LTO
Half Height LTO1 and LTO2 Tape Drive
Quick Installation Guide
Revision 4 February 2006
Mechanical Installation
For mechanical mounting specifications, please refer to Figure 1. Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the LEDs up. [. . . ] 43 32 64)
· Internal SCSI-LVD/SE-cable with 5 connectors · Internal, removable SCSI-LVD/SE-terminator · External, removable SCSI-LVD/SE-terminator · External SCSI 68HD/VHDCI 320MBs-cable
Termination
The SCSI-bus cable must be terminated in both ends according to SCSI specifications. If the tape drive is the last device on the bus, the bus must be terminated within 10 cm of the tape drive connection. Tandberg 220/420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98 Specification specifies that the termination of the SCSI-bus system is a part of the SCSI-cable and not a part of the SCSI-device. As a result, termination cannot be turned on or off directly on the tape drive itself. For internal devices, a SCSI-cable with an integrated terminator or a separate terminator applied to the end connector of the cable, 10 cm from the last device, must be used. External devices must be terminated with an external terminator on the last device on the SCSI-bus.
Software Installation
For Software Application support and software drivers, please see www. tandberg. com. For installation of Backup Application software, refer to the software vendor's software application user guide supplied with the software or on the software vendor's web.
4
Front LED Indicators
Figure 5
Light Emitting Diodes (LED)
Drive State
READY LED (Green left)
ACTIVITY LED (Green)
CLEAN LED (Amber)
FAULT LED (Amber right)
LED-test. Power-On Self-Test starts in parallel with the LED-test . Cartridge loaded, no activity Cartridge loaded, activity Cleaning Cartridge loading or unloading Unrecoverable drive failure Over temperature Media Error (wrong, write protected or harmed media)
ON
ON
ON
ON
OFF ON ON OFF OFF ON / OFF OFF OFF
OFF OFF Flashing Flashing Flashing OFF OFF Flashing
ON / OFF ON / OFF ON / OFF ON ON / OFF ON / OFF ON / OFF ON / OFF
OFF OFF OFF OFF OFF Flashing ON Flashing
Table 2
Front LED behavior during normal operation
5
Media and Capacities
To achieve and maintain the maximum quality of your Tandberg Data tape drive, we recommend using Tandberg Data media.
Drive Model Tandberg 220LTO Tandberg 420LTO LTO1, 2, 3 LTO Ultrium Generation 2 (Native format) LTO Ultrium Generation 1 (Read/Write compatible) Cleaning Cartridge for LTO1, LTO2 and LTO3 609 m 609 m 200 GByte 100 GByte 43 27 44 43 26 30 43 26 31 Media Name Tape Length 609 m Capacity (Native) 100 GByte Ordering no. 43 26 30
LTO Ultrium Generation 1 (Native format)
Table 3
Media alternatives
External Tabletop Enclosure
ON/OFF Switch Cooling Fan SCSI_ID Switch
Power Connector
SCSI Interface Connectors
Figure 6
External tabletop enclosure, rear side
Power Requirements
Tandberg 220/420LTO in external tabletop enclosure: AC Input: 100 VAC / 0. 6 A or 240 VAC / 0. 3 A, 50-60 Hz Tandberg 220/420LTO as standalone: DC Input (typical operation): 5 VDC / 2. 1 A, 12 VDC / 0. 6 A
Heat Dissipation
Tandberg 220/420LTO as standalone: Operating: 18 W Sleep mode with cartridge inserted: 9 W 6
Total customer satisfaction is of the utmost importance to Tandberg Data.
We guarantee that this product left our premises defect free. If you are not satisfied with the quality of this product, please contact your distributor or the nearest Tandberg Data office to have the problem solved!For more documentation and information, please see our website www. tandberg. com.
7
Tandberg Data
International headquarter
Tandberg Data ASA, Kjelsåsveien 161, Oslo, P. O. Box 134 Kjelsås, N-0411 Oslo, Norway. [. . . ] Tandberg Data Ltd. , Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury, Oxfordshire, OX15 4FF, United Kingdom Tel: +44 (0) 8450706916.
Specifications subject to change without notice. All trademarks are the property of their respective owners. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TANDBERG 220-420LTO
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TANDBERG 220-420LTO will begin.
