User manual TANDBERG MSERIES INSTALLATION

[. . . ] Tandberg Data M-Series Installation Guide Introduction Site Requirements 3 3 Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Cooling Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power and Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing a Desktop or Deskside Library 5 Installing a Desktop M1500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing a Deskside M2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing a Rack Mount Library 6 Determining the Position of the Shelves in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing the M1500 Rack Mount Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installing the M2500 Rack Mount Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installing the Library in the Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Installing Drives in the Library 31 Installing Tape Drives in an M1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Installing Tape Drives in an M2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Preparing and Inserting Tape Cartridges 34 Labeling Tape Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Document T6423046-02 A01, February 2004 1 Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Setting the Write-Protect Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Placing Cartridges in the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Connecting the Library to AC Power 41 M1500 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 M2500 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Connecting the Library to the Host Computer 45 SCSI Cabling Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Terminator Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 SCSI Cabling Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Powering Up the Library Disabling Unused Drive Bays 48 50 2 6207947-04fN 26 Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Introduction This document explains how to install a stand-alone M1500 or M2500. Note: To install an M1500 or M2500 module in a multiple library stack, refer to the Tandberg StackLink Installation Instructions (PN T6423049). 0 Site Requirements When selecting an installation site for the library, consider the following requirements: · · · · Space Requirements Cooling Considerations Environmental Requirements Power and Grounding 0 Space Requirements 0 Table 1 lists the dimensions of the M1500 and M2500 libraries. Caution: Allow at least 5 inches (12. 7 cm) of space behind the library to allow proper ventilation. Table 1 Library Dimensions M1500 Height Width Depth 6. 9 in. (726 mm) Cooling Considerations 0 Cooling is one of the most important factors to consider when selecting a location for the library. [. . . ] If you are installing the library in a rack with other equipment, place the heaviest equipment at the bottom of the rack. · 2 Verify that the rack mount shelves are level and securely fastened to the rack. 3 With the help of another person, lift the library onto the rack mount shelves. 4 Slide the library all the way into the rack. 5 Press the two buttons next to the left magazine access doors and open the doors. 6 Notice the two holes behind the left magazine access doors (see figure 26). These holes provide access to the rack mount clamp screws. Installing a Rack Mount Library 29 Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Figure 26 Securing the Library to the Rack Magazine access doors Access holes for the rack mount clamp screws 7 Insert a #2 POZIDRIV screwdriver into one of the holes and turn the rack mount clamp screw clockwise to tighten it fully. Caution: Do not overtighten the rack mount clamp screw. When the screw begins to feel tight, turn it an additional quarter turn and then stop. As you tighten this screw, a lever protrudes from the side of the library and presses against the back side of the rack rail. 8 Tighten the remaining rack mount clamp screw in the same manner. 9 Press the button next to the right magazine access door. 10 Repeat steps 6 through 8 to secure the right side of the library to the rack. 11 Close the magazine access doors. 30 Installing a Rack Mount Library Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Installing Drives in the Library This section explains how to install tape drives in the library. You will need the following tools for this procedure: · · · · #2 PHILLIPS® screwdriver (if you are installing drives in an M1500) TORX® T-20 screwdriver (if you are installing drives in an M2500) TORX T-8 screwdriver (if you are installing drives in drive bays 3 through 6 of an M2500) Flat blade screwdriver 0 Installing Tape Drives in an M1500 0 To install tape drives in an M1500: 1 At the back of the library, use a #2 PHILLIPS screwdriver to remove the cover plate protecting the drive bay in which you will install the tape drive. 2 Insert the tape drive into the drive bay slowly until the connectors are seated (see figure 27). 3 Tighten the tape drive thumbscrew using a flat blade screwdriver. 4 Repeat steps 1 through 3 to install another tape drive, if desired. Figure 27 Installing a Tape Drive in an M1500 Tape drive Thumbscrew Installing Drives in the Library 31 Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Installing Tape Drives in an M2500 0 To install tape drives in an M2500: 1 At the back of the library, use a TORX T-20 screwdriver to remove the cover plate protecting the drive bay in which you will install the tape drive. Note: The cover plates for drive bays 3 through 6 also have a TORX T-8 screw that must be removed to access the drive bay. Populate the drive bays in the following order: drive bay 1, drive bay 2, drive bay 4, drive bay 5, drive bay 6, drive bay 3 (see figure 28). Drive bay 3 is used only if six drives are installed in the library. Note: Figure 28 Drive Bay Numbering, M2500 Drive bay 2 Drive bay 1 Drive bay 3 (this drive bay is empty unless a sixth drive is installed) Drive bay 4 Drive bay 6 Drive bay 5 2 Insert the tape drive into the drive bay slowly until the connectors are seated (see figure 29). 32 Installing Drives in the Library Tandberg Data M-Series Installation Guide Document T6423046-02 A01 February 2004 Figure 29 Installing a Tape Drive in an M2500 Tape drive Thumbscrew 3 Tighten the tape drive thumbscrew using a flat blade screwdriver. 4 Install the appropriate cover plate in the space above the drive. Note: Two cover plates were provided with the tape drive. The smaller plate (215982 or 70-87502-01) used with tape drives on the middle level of the library; the larger plate (215981) is used with tape drives on the bottom level of the library. 5 Repeat steps 1 through 3 to install any additional tape drives. [. . . ] You can change these SCSI ID settings using the Drive ID and Library ID options on the GUI Configuration screen. Termination must be provided at each end of the SCSI bus (see Terminator Power). All SCSI cables must be shielded or double shielded to meet EMI specifications. The maximum total SCSI bus length for an LVD SCSI bus is 40 feet (12 meters). · · · Terminator Power 0 External terminators must be installed at the end of each SCSI bus. [. . . ]