User manual TANGENT EXEO AMP

[. . . ] CONTENTS SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS ACCESSORIES CONNECTIONS REMOTE CONTROL INFORMATION FRONT PANEL INFORMATION REAR PANEL INFORMATION OPERATION AND FUNCTIONS TROUBLESHOOTING GUIDE SPECIFICATIONS 1 2 4 5 7 9 10 11 13 14 SAFETY INFORMATION Caution: To reduce the risk of electric shock, do not remove Cover (or back) No user-serviceable parts inside. Refer servicing to qualified service personnel. This lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninstalled "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The symbol on this product indicates that it is of CLASS II (double insulated) construction. 1 IMPORTANT SAFETY INSTRUCTIONS CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. READ AND FOLLOW INSTRUCTIONS: All the safety and operation instructions should be read before the product is operated. Follow all operation instructions within this manual. [. . . ] Use pin-plug cords to connect the terminals to the INPUT terminals on the subwoofer. E. g. compact disc player Connect the CD terminals to the OUTPUT terminals on the compact disc player using the pin-plug cord. Speaker systems ACTIVE SUBWOOFER (NOT INCLUDED) To avoid damaging the speakers with a sudden high-level signal, be sure to switch the power off before connecting the O TPU U T speakers. Connect speaker with an impedance of 4 ohms or more. The amplifier's red speaker terminals are the + (positive) terminals and the black terminals are the ­ (negative) terminals. The + side of the speaker cable is marked to make it distinguishable from the ­ side of the cable. Connect this Recording connections Connect the REC OUT terminals to the input (LINE IN) terminals on the tape deck using the pin-plug cord. marked side to the red + terminals and the unmarked side is the black terminal. Prepare the speaker cords for connection by stripping off approximately 10 mm or less (no more as this could cause LI N E (I N R ) EC PLA O T) Y( U a short-circuit) of the outer insulation. Twist the wires tightly together so that they are not straggly. 1 A B 2 3 1. 3. Unscrew the knob Insert the speaker cable. Tighten the knob and secure the cable. 5 CONNECTIONS PHONO Connect the turntable's output cord L (white) plug to the L PHONO terminal and the R (red) plug to the R PHONO terminal. If your turntable is equipped with a grounding cable, connect it to the unit's GND terminal. But disconnect it if you notice increased humming. A DO UI AUX1 terminals This terminal have an electrical performance which is equivalent to that of the CD terminals which means that it can be used as the audio output terminals for a line level source. Connect this terminal to the OUTPUT terminal on the component using the pin-plug cord. AUX2 terminal This terminal has an increased sensitivity (x4) compared to the other line level inputs. Headphone terminal For connection of a pair of headphones. 6 REMOTE CONTROL INFORMATION By using the provided remote control unit, the receiver can be controlled from your listening position. To use the remote control unit, point it at the REMOTE SENSOR window of the receiver. Notes: - Even if the remote control unit is operated within the effective range, remote control operation may be impossible if there are any obstacles between the unit and the remote control. - If the remote control unit is operated near other appliance which generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it may operate incorrectly. Precautions concerning batteries -Be sure to insert the batteries with correct positive+ and negative ­ polarities. Never use different types of batteries together. [. . . ] Volume Control On the right hand side knob the volume can be adjusted. Menu Layout The menu is accessed by pressing and holding the left hand side knob, or by pressing AMP and then MENU on the remote. Use the arrow keys and the ENTER key of the remote, or the left hand side knob on the front panel to operate the menu. EQ ­ Bass Control The amplifier features a bass control with an adjustment of +/-10dB. EQ - Treble Control The amplifier features a treble control with an adjustment of +/-10dB. [. . . ]