User manual TANNOY PRESTIGE CANTERBURY SE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TANNOY PRESTIGE CANTERBURY SE. We hope that this TANNOY PRESTIGE CANTERBURY SE user guide will be useful to you.

Lastmanuals help download the user guide TANNOY PRESTIGE CANTERBURY SE.


Mode d'emploi TANNOY PRESTIGE CANTERBURY SE
Download
Manual abstract: user guide TANNOY PRESTIGE CANTERBURY SE

Detailed instructions for use are in the User's Guide.

[. . . ] OWNER'S MANUAL Estd. 1926 In combining the best of traditional crafts and the latest production and design skills Tannoy presents the Canterbury loudspeaker. The Canterbury embodies the Tannoy philosophy. Cabinets in selected hardwoods are hand finished and polished to a standard that is unsurpassed. The Canterbury 15 SE is a truly special loudspeaker made only to order with certification and personalised nameplate. [. . . ] This screening effect can give an improvement in detail clarity, depending on the amplifier used. Optimum results are achieved using a screened loudspeaker cable designed for such a system, such as the Tannoy TLC. Switch on the amplifier with the volume turned down. Select a favourite source and carefully turn up the volume. Check that bass and treble sounds come from both speakers. If not, switch off and remake the connections. Cables High quality audio signals passing from power amplifier to loudspeaker are unusual in their demands on cable. Frequencies from 20Hz to 20kHz (10 octaves or a ratio of 10, 000:1) and currents of 80dB dynamic range (again a ratio of 10, 000:1) have to coexist. The cable also has to be capable of transmitting peak currents of at least 10 Amp without causing losses greater than 0. 001 Amp (10 Amp divided by the ratio 10, 000). If the overall high frequency sound quality seems too prominent the -1. 5 or -3 positions for the ENERGY control should be tried. If the sound appears subdued in the treble region +1. 5 or +3 settings may be preferred. Once the ENERGY control setting has been established the ROLL OFF control can be adjusted to reduce or slightly increase the extreme high frequency content if necessary. Remember the changes that can be made by moving either control from one position to another are subtle. They may not easily be heard if the programme material has very little content in the frequency band under consideration. Choose a well balanced piece of music with a full spectrum of sound. The correct setting will be found when the loudspeakers are no longer evident and only the musical performance is heard. The low frequency output of the loudspeaker in the range 25 to 100Hz may be adjusted by operating the two sliding port openings on each side of the cabinet. Each port may be varied from fully open (full distributed port operation, both port slides in upper position) to fully closed (infinite baffle or acoustic suspension operation, both port slides in downward position). When both ports are fully open a very full rich bass response will be heard, when fully closed the bass response becomes more subdued. The correct setting is a matter for personal preference and local acoustic conditions. With one port open and the other closed the bass response will be 'level' and this position should be used for initial evaluation. How to adjust the Variable Distributed Port System for your music in your room Loudspeaker in corner Loudspeaker clear of wall Loudspeaker against wall PORTS Closed Open Either Closed or One Open The above suggestions are for guidance only. The music you listen to is also important - in general classical and light music will tend to sound more natural with the ports closed. Rock music will sound more exciting with one or both ports open. [. . . ] When a fault occurs in a hi-fi system the effect is always heard through the loudspeakers although they may not be the source of the fault. It is important to trace the cause of the problem as accurately as possible. A fault heard on one source (only CD or tape for instance) is most unlikely to be a loudspeaker problem. Loudspeakers do not generate hum, hiss or rumble although high-quality, wide-bandwidth loudspeakers may emphasise such problems. Tannoy Quality An important part of Tannoy's design philosophy is to produce loudspeakers with a level of performance beyond the most exacting specifications of contemporary source equipment. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TANNOY PRESTIGE CANTERBURY SE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TANNOY PRESTIGE CANTERBURY SE will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag