User manual TAPCO TWEEQ

[. . . ] 20 25 31. 5 40 50 63 80 100 125 160 200 250 315 400 500 630 800 1k 1. 25k 1. 6k 2k 2. 5k 3. 15k 4k 5k 6. 3k 8k 10k 12. 5k 16k 20k +12 LEVEL +17 HI-PASS LOW-PASS BYPASS RANGE 1 0 1 0 -12 DUAL 31- BAND GRAPHIC EQUALIZER BY T·231 +12 +17 0 40Hz 16kHz CLIP 6dB 12dB HI-PASS LOW-PASS BYPASS RANGE ON 2 20 25 31. 5 40 50 63 80 100 125 160 200 250 315 400 500 630 800 1k 1. 25k 1. 6k 2k 2. 5k 3. 15k 4k 5k 6. 3k 8k 10k 12. 5k 16k 20k 2 -12 LEVEL OFF POWER 40Hz 16kHz CLIP 6dB 12dB SERIAL /DATE CODE CHANNEL 1 WARNING NO OUTDOOR USE OUT OUT IN IN RISK OF FIRE REPLACE FUSE AS MARKED OUT IN BROUGHT TO YOU BY THE GROOVY FOLKS IN WOODINVILLE, WA, USA MANUFACTURED IN CHINA · FABRIQUE AU CHINE "TAPCO" AND "MACKIE" ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC. · COPYRIGHT ©2003 UNBAL BAL/UNBAL BAL BAL WWW. TAPCOGEAR. COM CHANNEL 2 OUT IN OUT IN OUT IN RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, T 315mA 250V AC 100-120V, 60Hz AC 200-240V, 50HZ RATED INPUT: 12. 5W LIFT GND AVIS: RISQUE DE CHOC ELECTRIQUE -- NE PAS OUVRIR DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL. UNBAL BAL/UNBAL BAL BAL by CAUTION AVIS 8. RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL Heat -- This product should be situated away from heat sources such as radiators, or other devices which produce heat. [. . . ] When the Input LEVEL control is in the center position, it provides no gain (unity gain). When the slider is all the way down the signal is off (-), and all the way up provides 17 dB of gain. 6. CLIP This LED lights when the output signal is within 5 dB of clipping. It is okay if the CLIP LED blinks occasionally, but if it blinks frequently or stays lit all the time, turn down either the LEVEL control or the output signal from the mixer or other device immediately preceding the T·231. 3. HI-PASS This button is used to roll-off the frequencies below 40 Hz. The LED below the button lights to indicate when the HI-PASS filter is turned on. This is useful to reduce stage rumble (low-frequency noise from footsteps picked up by microphones on stage) and microphone-handling noise. If the T·231 is used with monitor speakers, turning on this button can reduce the muddiness caused by the lows from the stage monitors feeding back into the main output through the microphones. 7. RANGE This determines the maximum boost and cut of the EQ sliders, either ±12 dB or ± 6 dB (pushed in). The corresponding LED below the RANGE button indicates the setting. The 12 dB setting provides more boost and cut if it is needed for more drastic EQ requirements. The 6 dB setting provides less boost and cut, but allows you to fine tune the controls with more precision. 8. POWER Use this switch to turn the T·231 on and off. The LED above the switch lights when the power is on. 4. LOW-PASS Use this button to roll-off the frequencies above 16 kHz. The LED below the button lights to indicate when the LOW-PASS filter is turned on. This is useful to remove hiss and high-frequency noise from the signal. 9 12 SERIAL / DATE CODE 13 IN CHANNEL 1 WARNING NO OUTDOOR USE OUT OUT IN RISK OF FIRE REPLACE FUSE AS MARKED 9 OUT IN 10 115V BROUGHT TO YOU BY THE GROOVY FOLKS IN WOODINVILLE, WA, USA MANUFACTURED IN CHINA · FABRIQUE AU CHINE "TAPCO" AND "MACKIE" ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC. · COPYRIGHT ©2003 UNBAL BAL/UNBAL BAL BAL WWW. TAPCOGEAR. COM CHANNEL 2 OUT IN OUT IN OUT IN RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, T 315mA 250V AC 100-120V, 60Hz AC 200-240V, 50HZ RATED INPUT: 12. 5W DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL. LIFT GND AVIS: RISQUE DE CHOC ELECTRIQUE -- NE PAS OUVRIR UNBAL BAL/UNBAL BAL BAL 11 REAR PANEL FEATURES 9. Line Cord Socket and Fuse Here is where you connect the detachable line cord that came in the box with your T·231. Plug the other end of the line cord into an AC outlet properly configured with the voltage required for your particular model (see AC Select Switch next). The fuse is located behind the fuse cover, at the bottom of the IEC socket. [. . . ] Final determination of warranty coverage lies solely with LOUD Technologies Inc. TAPCO products returned to LOUD Technologies and deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced within thirty days of receipt by LOUD Technologies at our rainforest factory complex. LOUD Technologies may use refurbished parts for repair or replacement of any product. Products returned to LOUD Technologies that do not meet the terms of this Warranty will be repaired and returned C. O. D. [. . . ]