User manual TASCAM CC-222MKII

[. . . ] D00822500A CD Recorder/Cassette Deck OWNER'S MANUAL Please note that to simplify the description, the model number is given in the Quick Start Guide as "CC-222" rather than "CC-222MKII". Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] 3 If recording is to start at the beginning of the cassette, make sure the cassette is stopped, otherwise, locate the cassette to the appropriate position where recording is to start, and enter record ready mode. NOTE Using the headphones with the MONITOR switch set to MIX will help here. 4 Press the DUB 2 key. Playback starts on the disc, and recording starts on the cassette. Bypassing the INPUT level for dubbing The INPUT control can be bypassed so that it has no effect when dubbing, in the following way: 1 2 Press the MENU key until the DUB>VOL item appears. Turn the dial to select either THRU (the control is bypassed and disabled) or ON (the control is enabled). NOTE This setting applies only to dubbing procedures, not to other recordings. It is not possible to make this menu setting (or any other menu settings) when dubbing is actually taking place. Recording tapes from the PHONO deck To record from an external record deck connected through the RIAA PHONO inputs: 1 2 Prepare for recording as described above (load a tape, set the REV MODE, etc. ). Press the MENU key until the PHONO > xxxx menu item is shown. If the display does not show PHONO > TAPE, turn the MULTI DIAL (or press the SKIP keys on the remote control) until it does 3 and press the MULTI DIAL (or ENTER on the remote control unit). The PHONO indicator lights on the display. If the tape is currently in stop mode, the tape rewinds, and the deck enters record ready mode (about eight seconds from the start of the cassette, to allow for leader tape). If the tape deck is already in record ready mode, it will remain in record ready mode. 18 TASCAM CC-222MKII Owner's Manual 3 ­ Cassette operations--Other recording features 4 5 Start playback of the record. Start recording with either the PLAY or PAUSE key. NOTE Press STOP (cassette deck) to stop the recording. The STOP key is the only key which is enabled during phono recording. After the phono recording has finished, the original tape signal source is restored. It is not possible to perform phono recording as described above under the following circumstances: a tape is not loaded or the tape is write-protected (the phono to tape function is disabled with no recordable tape inserted), or the tape is not either stopped or in record ready mode. Only recording as described above is possible from the RIAA PHONO sources to tape. Manual recording is not possible. Other recording features Recording silences between items At least four seconds of silence must be recorded between items on tape when using the search functions ("Search keys" on page 20). When recording, press and release either of the REC MUTE keys (main or remote). With the tape moving, the record source is muted for about four seconds (the display record indicator flashes), and the deck then enters record pause mode. Press PAUSE or PLAY to re-start recording. If the REC MUTE key is pressed while the deck is in record pause mode, four seconds of silence will be recorded on the tape, and the deck will return to record pause mode. If the REC MUTE key is held and pressed for longer than four seconds while recording is in progress, silence is recorded on the tape while the key is held down. The deck enters record pause mode when the key is released. Erasing tapes Anything previously recorded on the tape will automatically be erased when you make a new recording on it. It can also be erased by "recording" on it with the INPUT level control set to "0". Other tape functions and features Tape counter The tape counter value is incremented when the tape is moving from left to right, and decremented when it moves from right to left. Use either of the RESET keys (main or remote) to reset the value to 0000. [. . . ] There is no space on the disc, or no tracks are available, or a general recording error has or Cannot Rec!If it is a CD-RW disc, you may refresh it ("Refreshing a disc" on page 34), otherwise replace the disc. An error has occurred while trying to erase the disc. The display suddenly shows PMA Writing Either the disc is full (this message will be prefaced by Disc Full!! [. . . ]