User manual TASCAM SS-R1

[. . . ] » SS-R1 OWNER'S MANUAL D01014120A Solid State Stereo Audio Recorder IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a se rial numbe r located on the rear panel. [. . . ] You can specify a program of up to 99 tracks. · Pressing the remote's CLR/ESC key will delete the last-programmed track from the program. · If you attempt to program the 100th track, an error message of PROGRAM FULL will appear. A maximum of 99 tracks can be programmed. · If the total playback time of the programmed tracks exceeds 99 hours 59 minutes 59 seconds, the display will indicate --H--M--S. 1 While stopped, set the play mode to program play mode (see "Specifying the playback mode" on page 24). 2 Use the remote's numeric keys (0­9) to enter the desired track number for the program, and press the ENTER key to confirm it. The track will be registered in the program. NOTE 4 Press the PLAY key to begin program playback. NOTE Alternatively, you can use the front panel MULTI JOG dial to select a track and then press the MULTI JOG dial. · In program play mode, you won't be able to play unless at least one track has been registered in the program. · If you press the STOP key while stopped, all program data will be cleared. · The program data will be cleared when you switch the play mode. · The program data will be cleared when you poweroff the SS-R1. 3 Repeat step 2 to register each of the desired tracks in the program. NOTE · You can program the same track repeatedly. Switching the playback time display mode You can select the way in which the playback time is shown in the home screen. TOTAL and REMAIN are lit The remaining time in the play area is shown. NOTE 1 Press the front panel TIME (ESC) key (or the remote's TIME key). Each time you press this key, you will cycle through four types of time display. The currently selected display mode is shown above the time display area. No indicator The elapsed time of the current track is shown. REMAIN is lit The remaining time of the current track is shown. TOTAL is lit The elapsed time from the beginning of the play area is shown. · While stopped, the total playback time of the play area is always shown, regardless of whether TOTAL and REMAIN are lit. · In Program mode, the display area shows the elapsed time and remaining time of the entire program; not of the entire play area. · The time display mode setting is remembered even when the power is turned off. · For details on the time display during recording or in the record-ready condition, refer to "Switching the recording time display mode" on page 38. Power-on play The Power-on Play function starts playback automatically when the SS-R1 is powered-on. If this function is on and the POWER switch is pressed inward, you can use a commercially-available timer to power-on the SS-R1, and playback will begin automatically. 2 Make preparations for playback. Insert a CompactFlash card, and make the desired settings for the play area and the playback mode, etc. 3 Set the front panel POWER ON PLAY switch to the PLAY position. 4 Set your timer to the desired time. When the specified time arrives, the SS-R1 will be powered-on, and playback will begin automatically. 1 Connect the SS-R1 to a timer so that its power will be supplied from the timer. TASCAM SS-R1 5 - Playback Repeat playback You can repeatedly play back all tracks in the play area, or repeatedly play back a specified region within a track (A-B Repeat playback). Conventional repeat playback If you press the remote's REPEAT key to turn Repeat playback on, all tracks in the play area will play repeatedly (to do this on the SS-R1 itself, use menu mode). NOTE turn on repeat playback while stopped, repeat playback will begin when you press the PLAY key. To turn off repeat playback, press the remote's REPEAT key once again (or turn the PLAY menu item REPEAT to the OFF setting). The REPEAT indicator in the display will go dark. NOTE You can use the PLAY menu item REPEAT to turn on Repeat playback from the SS-R1 itself. REPEAT will light in the display. In this state, all tracks in the play area can be played back repeatedly. If you turn on Repeat playback during playback, playback will continue, and when it reaches the end of the play area, it will return to the beginning and continue playing. If you · By using repeat playback in conjunction with Single playback, Program playback, or Random playback, you can repeat a single song, repeat a program, or repeat random playback. · The repeat function on/off setting is remembered even when the power is off. A-B Repeat playback This lets you specify a desired region (A-B) within a track that will be played back repeatedly. NOTE 1 While playing or stopped, press the remote's A-B key at the starting point (A) of the region that you want to repeat. In the home screen, the REPEAT and A- indicators will blink. NOTE · If you press the STOP key to stop playback, the specified region (A-B) will be cleared. · You can't specify A-B repeat playback across tracks. In the home screen, A-B will light (in addition to REPEAT). [. . . ] Play or pause is not possible because no program has been registered. Search was not possible because the specified search time (search track) does not exist. Recording is not possible because the media does not meet the system requirements. There is a discrepancy between the specified playlist and the media information. [. . . ]