User manual TASCAM TM-D1000 FX-D1000 INSTALL

[. . . ] The display should read: Option Monitor > Mode V 2) Push DATA ENTRY button downwards 4 times until "SYSTEM" appears. Option Monitor System > V 3) Rotate "DATA ENTRY(PUSH)" knob clockwise until the version appears. TM-D1000 < Ver1. 18 If the software version is LESS than 1. 18, the internal programmable logic device (PLD) must be updated. Included in this FX-D1000 package is a new PLD with the most current software available at the time of manufacturing. [. . . ] If you need to upgrade continue on to step 3. UPGRADING THE TM-D1000 INTERNAL PLD TO THE LATEST SOFTWARE REVISION LEVEL: STEP 3: Removing U17, Main PLD: Locate U17 on the Main PCB as shown in the diagram (Figure 1. 2). The PLD is held in place with a rectangular black plastic locking device. Slide the locking device down or toward you. Remove it by lifting straight up from the main PCB. Remove the PLD and place it TASCAM TEAC Professional Division 7733 Telegraph Road Montebello, CA 90640 Phone (323) 726-0303 Fax (323) 727-7632 FX-D1000 10/08/99 Page 3 of 6 INSTALLATION INSTRUCTIONS into the plastic case supplied with the new PLD. Place it into the postage paid self-addressed envelope provided and return to TASCAM. STEP 4: Installing the new PLD: CAUTION: The PLD is sensitive to static discharges and may be damaged if improperly handled. It is highly recommended that the installer be well grounded before handling the device: Detach Attach Note the orientation of the small dot on the PLD. It must be installed with this dot in the lower right corner as shown in the diagram to the right. On the main PCB, the white silk-screened outline of U17 also shows a small white dot in the lower right corner. After aligning the locator dots, lay the PLD into position. Secure the PLD by placing the rectangular black plastic locking device over the PLD. After it is set in place, sliding the locking device upwards will lock it into position. (See the diagram above and to the right. ) STEP 5: The software has now been upgraded in your TASCAM TM-D1000. INSTALLING THE FX-D1000: IMPORTANT Remove the protective spacer that is installed in connector CN1 before proceeding. STEP 6: Locate the three plastic standoffs in the package with the FX-D1000 effects module. Using the diagram (Figure 1. 3), locate the position for these standoffs on the Main PCB and install one standoff in each of the three holes. TASCAM TEAC Professional Division 7733 Telegraph Road Montebello, CA 90640 Phone (323) 726-0303 Fax (323) 727-7632 FX-D1000 10/08/99 Page 4 of 6 INSTALLATION INSTRUCTIONS Orient the FX-D1000 with the components facing the main PCB. FX-D10000 Locations for the plastic standoffs FIGURE 1. 3 STEP 7: Remove the FX-D1000 from its anti-static wrapping. Holding the FX-D1000 by its edges, orient it as shown in Figure 1. 3. The component side of the board should be on the bottom. STEP 8: The connector on the FX-D1000 should be inserted into connector CN5 on the main PCB. Fit the three retaining studs you installed into the Main PCB into the corresponding holes on the FXD1000. After insuring the pins on the connector and the retaining studs are aligned properly, press the FX-D1000 firmly into place. [. . . ] The table on the next page shows all the effects patterns available. The first table represents the "Effect Pattern Menu" prior to the installation (6 patterns). The second table represents the new "Effects Pattern Menu" following the installation of your new FX-D1000 (20 patterns). TASCAM TEAC Professional Division 7733 Telegraph Road Montebello, CA 90640 Phone (323) 726-0303 Fax (323) 727-7632 FX-D1000 10/08/99 Page 6 of 6 INSTALLATION INSTRUCTIONS TABLE FOR OPTION/EFFECT/EFFECT PATTERN LCD System Without FX-D1000 1st line Effect_Pattern__________ 2nd line Ch_Dynamics____________?Ch_Dymanics[8ch]________ Ch_Dynamics+Aux1-2+L-R_? [. . . ]