User manual TECOM AR1061 DATASHEET

[. . . ] 6 REAR PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CONNECTING THE HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the ADSL cable and optional telephone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn on and boot up your computer(s) and any LAN devices such as hubs or switches. Step 5. Configure the AR1061 through the WEB interface The detail step3 would be described in Chapter3. It would help you configure the AR1061 to meet your need. Step 6. Save the configurations and Reboot. To make the settings you made on AR1061 take effect. -9- Manual Ver1. 01 3. Configuration 3. 1 Setup Step 1: Connect the ATU-R and PC with a cross-over/straight Ethernet cable. Step 3: The default IP of the ATU-R is 192. 168. 1. 1. 3. 2 Establish The Connection Enter the IP address (default is 192. 168. 1. 1) of ATU-R from the Web Browser. . A Dialogue Box will be popped up to request the user to login. Authentication Please enter the management username/password into the fields then click on the OK button (default username/password is admin/admin). If the authentication passes, the home page "Device Info - Summary" will be displayed on the browser. (Figure 2) - 10 - Manual Ver1. 01 Figure 2. ATU-R Home Page - 11 - Manual Ver1. 01 Link State ­ Statistics ­ ADSL - 12 - Manual Ver1. 01 3. 3 Quick Setup The system administrator can configure the ATU-R remotely or locally via a Web Browser. Network configuration need to be planned and decided before starting the configuration procedure. Quick Setup allows system administrator to select the appropriate operation mode and configure the corresponding settings step by step to create a connection. Quick Setup ­ ATM PVC Configuration Give the VPI/VCI values. Please contact you ISP for the information. Click on "Next" to go to next step. - 26 - Manual Ver1. 01 3. 3. 3. 2 Connection Type Figure 16. Quick Setup ­ Connection Type and Encapsulation Mode Select "Bridging", and the "Encapsulation Mode". Please contact you ISP for the information. Click on "Next" to go to next step. - 27 - Manual Ver1. 01 3. 3. 3. 3 WAN Service Figure 17. Quick Setup ­ WAN Service Give a service name (default setting is br_0_33) and check the box to enable this wan service. Click on "Next" to go to next step. - 28 - Manual Ver1. 01 3. 3. 3. 4 Device Setup Figure 18. Quick Setup ­ Device Setup Give LAN IP (default 192. 168. 1. 1) and Subnet Mask (default 255. 255. 255. 0). Click on "Next" to go to next step. - 29 - Manual Ver1. 01 3. 3. 3. 5 WAN Setup ­ Summery Figure 19 Quick Setup ­ WAN Setup ­ Summary The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISP, and then click on "Save/Reboot" button to complete the configuration procedure. - 30 - Manual Ver1. 01 3. 3. 4 MAC Encapsulation Routing (MER) Configuration Click on "Quick Setup" in the left frame, and follow the steps below to create a MAC Encapsulation Routing (MER) connection. [. . . ] Consult your ISP, make sure that the settings match the settings provided by it. - 52 - Manual Ver1. 01 3. 5 Diagnostics This page allows users to test the Ether port connection, DSL port connection, connection to the Internet Service Provider. If a test displays a fail status, click "Test" again to make sure the fail status is consistent. If the test continues to fail, click "Help" to follow the troubleshooting procedure. 3. 6 Management The system administrator can do the following functions to manage the configurations, events, SNMP information, user accounts, and software update of the ATU-R. Settings - Backup/Update Settings and Reset to Default System Log SNMP Agent Access Control ­ Services, IP addresses, and Passwords Update Software Save / Reboot - 53 - Manual Ver1. 01 3. 6. 1 Settings­Backup/Update Settings and Reset to Default System Administrator can do the ATUR settings backup, update, and restore here. [. . . ]