User manual TEFAL CB7031 11-05

[. . . ] 40 3 IMPORTANT SAFETY INSTRUCTIONS Read these Operating Instructions carefully before installing or using the Ventilation System. This appliance is intended for residential use only. Use the appliance only for its intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of the hood. This appliance complies with current safety requirements. [. . . ] The indicators show which power level has been chosen. 11 Operation Turning the light on Turning the light off The light for illuminating the cooktop can be turned on or off independently of the fan. ^ Pull the deflector plate out 1. 5" (3 cm). ^ When the light is turned on the indicator next to the button illuminates ^ Press the light button again. The next time the deflector plate is pulled out the light will come back on. 12 Cleaning and care Stainless steel surfaces Before servicing or cleaning the hood, disconnect it from the power supply by "tripping" the circuit breaker or unplugging it. Make sure power is not restored to the appliance while maintenance or repair work is performed. Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can be applied. Grease filter The reusable metal grease filters remove solid particles from the vented kitchen air like grease and dust, etc. The hood has an external filter which is visible from beneath. An internal filter is situated above the external filter within the casing. The grease filters should be cleaned every 3-4 weeks or whenever the grease filter indicator lights. Dirty filters are a fire hazard. Cleaning the casing Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. USA 1-800-999-1360 CDN 1-800-565-6435 WARNING: THIS APPLIANCE MUST BE GROUNDED Important The hood comes equippped with a 5 ft (1. 5 m) power cord with a NEMA 5-15 molded plug for connection to a 120 VAC, 60 Hz, 15 A power outlet. 15 A 21 Appliance dimensions CB7031-1 i DA 329-1 i * 1) The slot for the active charcoal filter must be accessible if the hood is being used in recirculation mode. 2) The rear panel of the cabinet may have to be removed for these dimensions to be applicable. (See built-in depth of the upper cabinet). 3) DFB light shield (optional accessory) To ensure that the exhaust ducting can be installed on the exhaust connection easily, the upper cabinet must be at least 18 1/8" (460 mm) high. *The DA 329-1 i can also be built into a 23 5/8" (60 cm) cabinet. (See upper cabinet measures for CB7031-1 i). In this case, the lower portion of the hood will overlap the bottom cabinets on either side. 22 Appliance dimensions Metric conversion table Millimeters 3 10 15 19 30 40 50 70 75 85 88 125 150 170 175 190 245 255 258 270 273 275 285 345 420 460 470 562 568 595 600 895 900 6 Inches 1 3 9 /8 /8 /4 /16 3 1 /16 1 9/16 1 15/16 2 3/ 4 3 3 3/ 8 3 1/ 2 5 6 11 3 /16 6 7/ 8 7 1/ 2 9 5/ 8 10 1/16 10 3/16 10 5/8 10 3/4 10 13/16 11 1/4 13 9/16 16 9/16 18 1/8 18 1/2 22 1/8 22 3/8 23 7/16 23 5/8 35 1/4 35 7/16 23 Appliance dimensions Installation in cabinetry The depth of the installation depends on what type of light shield is used and the dimensions of surrounding cabinetry. Hood installed with a DFB light shield (optional accessory) To install the hood so that the light shield is flush with the adjacent cabinetry, the following dimensions must be used. (Please refer to the metric conversion table) Hood installed with a custom made light shield A custom made, matching light shield can be mounted on the hood. To do this the minimum cabinet depth must be 10 13/16" (275 mm). [. . . ] ^ Plug in the power cord. 36 Installation Special installation instructions 27 9/16" (70 cm) width cabinet 35 7/16" (90 cm) width cabinet ^ The measure "x" will be calculated as described for a 23 5/8" (60 cm) cabinet. ^ Screw the spacer block to the cabinet using 4. 0 x 16 mm screws with the lower edge flush with the cabinet. ^ Screw the runners according to the thickness of the cabinet walls with either the imprint "16 mm" or "19 mm" to the spacer blocks using 3 self tapping screws 3. 5 x 9. 5 mm on each side. ^ Insert the supplied 3. 5 x 9. 5 mm screws to cover the 4 drill holes in the casing. 37 Air extraction Danger of toxic fumes. [. . . ]