User manual TEFAL CM2020

[. . . ] 27 Plywood backing Installation Installation instructions . 32 Air extraction Electrical connection Technical data 2 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. Read these instructions carefully before installing or using the Ventilation System. Use the appliance only for its intended purpose. , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ~ a) Use this appliance only in the manner intended by the manufacturer. [. . . ] ­ A time of 20 hours should be programmed in kitchens with frequent pan or deep frying. ­ A time of 20 hours should also be programmed if the kitchen is only used occasionally to prevent grease which has accumulated over a long period of time from hardening on the filters, making cleaning more difficult. Reprogramming the grease filter timer The indicator for the grease filter and one of the "­/+" indicators will flash. The lit indicator shows the programmed time: 1st indicator from the left 2nd indicator from the left 3rd indicator from the left 4th indicator from the left = = = = 20 hours 30 hours 40 hours 50 hours ^ Use the "­/+" button to select the desired time. ^ Store the selection by pressing the grease filter button. ^ Press the On/Off button to turn off the fan. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. ^ Press the Delayed Shut Down and grease filter buttons at the same time. 15 Operation Reprogramming the charcoal filter timer The active charcoal filter can only be used in recirculation mode and cannot be used to exhaust fumes. The charcoal filter timer is not preset. Before using the hood in recirculation mode, the charcoal filter timer must be programmed. The indicator for the charcoal filter and one of the "­/+" indicators will flash. The lit indicator shows the programmed time: 1st indicator from the left = 120 hours 2nd indicator from the left = 180 hours 3rd indicator from the left = 240 hours 4th indicator from the left = deactivated ^ Use the "­/+" button to select the desired time. ^ Turn off the fan using the On/Off button. ^ Press the Delayed Shut Down and charcoal filter buttons at the same time. ^ Store the selection by pressing the charcoal filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. 16 Cleaning and Care , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. powder or cream cleansers, ­ abrasive sponges, e. g. Do not use the pure detergent, aggressive all purpose cleaners, oven sprays or limescale removers. If the filters are incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the casing. ^ After returning the grease filters, press and hold the grease filter button for 3 seconds to reset the timer. ^ If the grease filters are cleaned before the grease filter timer has reached its maximum, press the grease filter button for 6 seconds to reset the counter to zero. The grease filters should be cleaned every 3 - 4 weeks, when the grease filter indicator lights, or when they are visibly dirty, whichever comes first. , A dirty filter is a fire hazard. 18 Cleaning and Care Active charcoal filter In recirculation mode an active charcoal filter must be used in addition to the grease filters. The active charcoal filter will be replaced in the canopy above the grease filters. Replacement active charcoal filters can be ordered from Miele. ^ Remove the grease filters to access the charcoal filter. See "Cleaning and Care - Grease filters". Before using: ^ Program the charcoal filter timer, see "Operation / Reprogramming the charcoal filter timer". Replace the active charcoal filter when the charcoal filter indicator lights, at least every 6 months or when they no longer absorb odors efficiently. ^ After replacing the charcoal filter, press and hold the charcoal filter button for about 3 seconds to reset the charcoal filter timer. ^ If the charcoal filter is replaced before the timer has reached its maximum, the charcoal filter button should be pressed for 6 seconds to reset the counter to zero. 19 Cleaning and Care Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". When in use halogen bulbs become extremely hot, and can burn your hands. [. . . ] Exhaust ducting and connections ­ The ducting should be as short and straight as possible, and the number of sharp bends should be minimized. ­ For most efficient air extraction, the diameter of the ductwork should not be less than 6" (150 mm). Use of flat ducts also reduces the air extraction efficiency. ­ Noise levels of the hood will increase if flat ducts or round ducts of less than 6" (150 mm) in diameter are used. [. . . ]