User manual TEFAL DELISNACK

[. . . ] Temperature control dial Soleplate C D s MOISTENING THE LINEN (SPRAY) - When steam or dry ironing, press several times on the Spray Button to moisten the linen (G) and to remove stubborn creases. - Make sure that there is water in the tank before using this button. G WARNING!Remove the soleplate protector before heating up the iron (depending on the model) Warning!Before using your iron with the steam function for the first time, we recommend that you operate it in horizontal position for a few moments, away from your linen, ie press several times on the double steam button. [. . . ] · Set it at the minimum position for wool. E Recommendations: Fabrics and ironing temperatures: · Your iron heats up quickly : begin by ironing those fabrics that are ironed at low temperatures, then go on to those requiring a higher temperature; · If you turn down the thermostat, wait until the thermostat light comes back on before ironing again. · When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate of the fabrics. What water to use? Your appliance has been designed to function with tap water. However, it is necessary to operate the Self-Clean function regularly to clean the steam chamber and eliminate hard water deposits. If your water is very hard you may mix tap water with distilled water in the following proportions: 50% tap water, 50% distilled water. Types of water not to use: Heat concentrates the elements contained in water during evaporation. The types of water listed below contain organic waste or mineral elements that can cause spitting, brown staining, or premature wear of the appliance: water from clothes dryers, scented or softened water, water from refrigerators, batteries, or air conditioners, pure distilled water, or rain water. 2. - Set the steam control on DRY (see diagram A). - You may start ironing when the thermostat light goes out. 5- IS THERE A PROBLEM ? Problems · Water drips from the holes in the soleplate Possible causes Solutions · The chosen temperature is too low and does not allow for · Set the temperature control dial in the coloured zone (from qq to MAX) the formation of steam. · You are using steam while the iron is not hot enough. · Wait until the indicator light goes out. Unplug your iron and let it cool down before cleaning it s CLEANING THE ANTI-CALC VALVE (Once per month): - Unplug your iron and empty the water tank. - To remove the anti-calc valve, pull it up using the tabs located on each side (H) NEVER TOUCH THE END OF THE VALVE - Soak the valve in a cup of white spirit vinegar or plain lemon juice for 4 hours (I). - Plug in your iron and wait until the thermostat light goes out. - Unplug the iron and hold it over a sink in the horizontal position. - Shake the iron gently, over the sink, until all of the water in the water tank (with the impurities) has flowed out via the soleplate. - At the end of the operation, put the anti-calc valve back into position. - Turn the iron back on for 2 minutes, setting it on its heel, to dry the soleplate. - Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth. Recommendation : The self-cleaning function helps to delay the scaling of your iron. DO NOT USE CHEMICAL DESCALING AGENTS s CLEANING THE SOLEPLATE: - While the sole plate is still just warm, clean it by rubbing it with a moist, non-metallic pad. HELPLINE : If your have any problem or queries, please call our Customer Relations Team first for expert help an advice on : Or consult our web site : www. tefal. co. uk 0845 602 1454 ­ UK (01) 4751947 ­ IRELAND This product has been designed for domestic use only. Any professional use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no resposibility and the guarantee will not apply. FOR YOUR SECURITY · Warning!The voltage of your electrical installation must correspond to that of the iron (220V-240V AC or 127 V depending on the model). Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee. [. . . ] · This iron must always be plugged into an earthed socket. · If using a mains extension lead, ensure that it is correctly rated (10A or 13A for UK only), with an earth. · If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger. · Never immerse your iron in water! [. . . ]