User manual TEKTRONIX 80E09 DATASHEET

[. . . ] This allows for differential or common mode TDR or S-parameter testing of two coupled lines, in addition to the independent testing of isolated lines. The independent step generation for each channel allows true differential measurements, which ensures measurement accuracy for differential devices. The 80E10 and 80E08 are small form factor, fully integrated independent 2-meter remote sampler systems, enabling location of the sampler near the DUT and ensuring the best signal fidelity. An optional 2-meter extender is available for the 80E04. [. . . ] Both of these modules can be used with the optional 2-meter extender cable, which ensures superior signal fidelity and measurement flexibility. The 80E03 and 80E03-NV are dual-channel, 20 GHz sampling modules. These sampling modules provide an acquisition rise time of 17. 5 ps or less. An optional 2-meter extender cable is available. When used with Tektronix 80SJNB Jitter, Noise, and BER software, these modules enable separation of both jitter and noise into their components, understanding precise causes of eye closure, and obtaining highly accurate extrapolation of BER and 3-D eye contour. When used with the 82A04 phase reference module, time-base accuracy can be improved down to 200 fsRMS jitter, which together with the 300 V noise floor and 14 bits of resolution ensures the highest signal fidelity for the measured signals. 2 www. tektronix. com Electrical Sampling Modules -- 80E10 · 80E09 · 80E08 · 80E07 · 80E06 · 80E06X2 · 80E04 · 80E03 · 80E03-NV · 80E01 Characteristics Characteristic Application Type Channels Input Impedance Channel Input Connector Bandwidth*2 80E10 True differential TDR, S-parameters, and fault isolation High-frequency, low-noise signal acquisition and jitter characterization True differential TDR and S-parameters Optimal noise/performance trade-off for jitter characterization High-speed electrical device characterization TDR impedance and crosstalk characterization Device characterization High-frequency, high maximum operating range signal acquisition 2 50 ±1. 0 80E09 2 50 ±1. 0 80E08 80E07 80E06 2 2 1 50 ±1. 0 50 ±1. 0 50 ±0. 5 1. 85 mm female, precision adapter to 2. 92 mm included with 50 SMA termination 1. 85 mm female, precision adapter to 2. 92 mm included with 50 SMA termination 2. 92 mm female 2. 92 mm female 1. 85 mm female, precision adapter to 2. 92 mm included with 50 SMA termination 3. 5 mm female 3. 5 mm female 2. 4 mm female, precision adapter to 2. 92 mm included with 50 SMA termination 50/40/30 GHz*3, 4 60/40/30 GHz*3, 4 30/20 GHz*3, 4 30/20 GHz*3, 4 70+ GHz 80E04 80E03 80E03-NV 80E01 2 2 1 50 ±0. 5 50 ±0. 5 50 ±0. 5 20 GHz*3 20 GHz*5 50 GHz *2 Values shown are warranted unless printed in an italic typeface which represents an unwarranted characteristic value that the instrument will typically perform to. *3 Calculated from 0. 35 bandwidth rise time product. *5 The 80E03 bandwidth is calculated from 0. 35 bandwidth rise time product. G5 ­ Complete Care 5 Years (includes loaner, scheduled calibration and more). R3 ­ Repair Service 3 Years (including warranty). R5 ­ Repair Service 5 Years (including warranty). Opt. D1 ­ Calibration Data Report (not available with 80E07 - 80E10). D3 ­ Calibration Data Report 3 Years (with Opt. D5 ­ Calibration Data Report 5 Years (with Opt. G3 ­ Complete Care 3 Years (includes loaner, scheduled calibration and more). Interconnect Cables (3rd party) Tektronix recommends using quality high-performance interconnect cables with these high-bandwidth products in order to minimize measurement degradation and variations. Gore & Associates' cable assemblies, accessible at www. gore. com/tektronix, are compatible with the 2. 92 mm, 2. 4 mm, and 1. 85 mm connector interface of the 80Exx modules. Assemblies can be ordered by contacting Gore (at the URL above). Calibration Kits and Accessories (3rd party) To facilitate S-parameter measurements with these electrical modules and IConnect® software, we recommend precision calibration kits, adapter kits, connector savers, airlines, torque wrenches, and connector gauges from Maury Microwave. These components, accessible at www. maurymw. com/tektronix. htm, are compatible with the 2. 92 mm, 2. 4 mm, and 1. 85 mm connector interface of the 80Exx modules. Cal kits and other components can be ordered by contacting Maury Microwave (at the URL above). Other Accessories 80E07 - 80E10). Sampling Module Extender Cable (2-meter length) ­ Order 80N01 (not for use with 2X Attenuator (SMA Male-to-Female) ­ Order 015-1001-xx. [. . . ] and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. [. . . ]