User manual TELEMECANIQUE ALTIVAR 31

[. . . ] If this is your first experience having soft, conditioned water in your home, you'll be amazed at the marvelous difference it makes. We promise that you'll never want to be without it again. Congratulations, too, on selecting one of the "first family" of water conditioners in the prestigious Culligan Medallist Series. With Culligan's many years of knowledge and experience in water treatment, you can be confident that the model you selected has been designed and engineered to provide years of service with a minimum of care and attention. [. . . ] Note: Changing this setting will cause the unit to load the Filter or Softener defaults. SOF OFF 4. Timeclock Backup Press the "STATUS" key. The display will blink "dIP4" for 3 seconds and then show the current status. Toggle between "OFF" (Timeclock backup is off) and "ON" (Timeclock backup is on) with the "+" or "-" key. Note: Changing this setting will not change any of the programmed values and will load the default Timeclock Backup value of 3 days. Programming step 7 will be activated when this is set to On. Note: This option will only be available when the flowmeter is plugged into the control. English or Metric Press the "STATUS" key. The display will blink "dIP5" for 3 seconds and then show the current status. Toggle between "En" (English units) and "MET" (Metric units) with the "+" or "-" key. 12 or 24 Hour Clock Press the "STATUS" key. Adjust the setting with "+" or "-" key. (1-40 minutes) 19 Programming (cont. ) Step 5 ­ Programming Brine Draw/Slow Rinse Time Press the "Status" key after programming the backwash time. The display will blink "br" for 3 seconds and then display the brine draw/slow rinse time in minutes. Adjust the setting with the "+" or "-" key. See Table 5 for suggested brine draw/slow rinse times. Note: This option will not show if the control is set to Filter mode. Step 6 ­ Programming Gallons (Liters) or Days to Regeneration Meter Mode Press the "Status" key after programming the brine draw/slow rinse time. The display will blink "CAPG" ("CAPL") for 3 seconds and then display the gallons or liters set point. Adjust the setting with the "+" or "-" key. (10-9990 Gallons)(40-37000 Liters) Note: The programmed value must be multiplied by 10 to obtain the actual setting. For example, if 87 is shown in the display, the control will regenerate after 870 gallons have passed through the meter. 71 OR 87 Timeclock Mode Press the "Status" key after programming the brine draw/slow rinse time. [. . . ] Date of Installation SETTINGS Salt Setting _________ lbs. Regeneration Interval __________ days (Time clock models) Gallons to signal __________ gallons (Soft-Minder® models) Catalog No. Tank Serial No. Number of people in household WATER ANALYSIS Total Hardness _______ (gpg) Other _________________________________________________________________________ _________________________________________________________________________ Total Iron _______ (ppm) pH (acidity)____________ 48 Culligan Medallist Series® Automatic Water Conditioners You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan specifications, against defects in material and workmanship from the date of original installation, as follows: For a period of ONE YEAR For a period of FIVE YEARS For a period of TEN YEARS The entire conditioner The AccuSoft® circuit board, or Soft-Minder® meter, if so equipped The control valve body, excluding internal parts The conditioner tank The salt storage container, brine valve and all its component parts The Cullex® resin Culligan Limited Warranty For the LIFETIME of the original consumer purchaser If a part described above is found defective within the specified period, you should notify your independently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect the water conditioner on your premises. [. . . ]