User manual TERRATEC PHASE28

[. . . ] TERRATEC PRODUCER/PHASE 28 English Manual Version 1. 0, last revised: June 2003 CE Declaration We: TerraTec Electronic GmbH, Herrenpfad 38, D-41334 Nettetal, Germany hereby declare that the product: PHASE 28, to which this declaration refers, is in compliance with the following standards or standardizing documents: EN 50013, EN 50022 The following are the stipulated operating conditions and environmental conditions for said compliance: residential, business and commercial environments and small-company environments. This declaration is based on: Test report(s) of the EMC testing laboratory The information in this document is subject to change without notice and shall not be deemed as a warranty by the seller. No warranties, express or implied, are made with regard to the quality, suitability or accuracy of this document. The manufacturer reserves the right to change the contents of this document and/or the associated products at any time without the provision of prior notice to specific persons or organizations. [. . . ] The system requirements are OS10. 1 or higher. Furthermore, in order to install the drivers, you must have administrator rights on the system. To install the PHASE 28 MAC OS X ­driver and the ControlPanel application, select the program PHASE 28 OS10 Installer. pkg from the directory <CD>:\PHASE 28\Driver\MAC\ of the PHASE 28 product CD. For identification, enter your name and your OS X password. During installation, you will be asked for the target drive; select the desired target drive. Follow the instructions of the installer and complete the installation by rebooting your system. After restarting the system, you can select the PHASE 28 ControlPanel from the directory Macintosh HD -> Programs. PHASE 28 (English) 15 The connections of the PHASE 28 system. The PHASE 28 audio interface offers you numerous connections for connecting professional studio peripherals. Following is a detailed overview of its technical and electrical characteristics: The PHASE 28 PCI system 16 PHASE 28 (English) 1. Connection for the PHASE 28 cable adapter. Please ensure that the connector strip is firmly screwed onto the PCI system, as the weight of the cable can otherwise cause it to come unplugged. Here, the present signal can be optimally adjusted to the converter level. Any clipping is indicated by the corresponding LED (3). As soon as the signal reaches the clipping level (1dB @ 2. 1 Volt RMS, 1kHz), the LED is lit. In this case, push back the gain with the appropriate gain controller (2) until the LED stops blinking. If the setting range is not sufficient to go below the clipping range, reduce the output level on your external equipment (e. g. Here, the present signal can be optimally adjusted to the converter level. Any clipping is indicated by the respective LED (4). As soon as the signal reaches the clipping level (1dB @ 2. 1 Volt RMS, 1kHz), the LED is lit. In this case, decrease the amplification using the appropriate gain controller (4) just to the point where the LED stops blinking. If the setting range is not sufficient to go below the clipping range, reduce the output level on your external equipment (e. g. For the internal synchronization of up to 4 EWS/PHASE PCI cards (5 contacts, the jumper must remain on the master card). For more information, please read Chapter "Cascading and internal synchronization. " starting on Ü page 32. [. . . ] The stereo link function (enabled by default) permits the left and right signals to be adjusted simultaneously. PHASE 28 (English) 31 Cascading and internal synchronization. The functions listed in the following sections will be available in future software updates. Check out www. terratec. com every so often for news about current updates. Up to 4 TerraTec audio interfaces can be installed in a computer, and can even be operated in a closed system, if they have what are known as EWS connections. You can therefore conveniently increase the number of input and output channels which can also access directly from most Windows/MAC applications. A fully loaded system containing four PHASE and/or EWS models thus features a total of 40 inputs and outputs - and all of that with virtually the same low latency! [. . . ]