User manual THERMADOR 14-10-387E

[. . . ] Lock service panel to prevent power from being turned ON accidentally. Avant l'installation, COUPER au tableau de service, et fermer a clef le tableau de service pour empecher l'alimination d'etre allumée per hasard. AVERTISSEMENT: IMPORTANT: LOCAL CODES VARY. INSTALLATION, ELECTRICAL CONNECTIONS AND GROUNDING MUST COMPLY WITH ALL APPLICABLE CODES. Check your local building codes for the proper method of installation. In the U. S. A. , if there are no applicable local codes, this unit should be installed in accordance with the National Fuel Gas Code #Z223. 1-Current Issue, and the National Electrical Code ANSI/NFPA No. [. . . ] Insert cord connector into receptacle located in lower right plenum bottom. See Figure 7. Integral Blower Front Rail Receptacle Plenum Opening Figure 7 ­ Blower Cord Connection Blower Cord OVEN FRONT 2. Units using Remote Blower: a) Wiring the Remote Blower Wire connections between the range and remote blower shall be made as follows: 1. Remove plenum cover and front rail for access to range blower wiring. Grasp the five wires and cut as close to molded connector as possible. Remove plug from electric "knockout" from plenum bottom (right front corner). Secure remote blower flex conduit/wiring to plenum conduit connector, 4. Connect color coded range wires to remote blower wires using wire nuts or approved splices. Reinstall plenum cover and front rail. Figure 8 ­ Remote Blower Wiring Plenum Opening Removable Plenum Cover Screws Wiring Compartment To Remote Blower Duct Attachment Box Removable Front Rail K. O. 's Location Range Front Figure 9 ­ Range - Remote Blower Electrical Connection Range White Black Red Blue Black Blue Red White Red Molded Connector Remote Blower Blue White Black Green Green 7 I INSTALLING THE VENTILATION INSTALLING A REMOTE BLOWER CAUTION - For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. NOTE: Remove and discard shipping bracket (attached to bottom of motor and inlet collar). An Integral Blower Model VTN30Q or Remote Model VTR1000Q Blower System must be installed with the range. (Blower systems are purchased separately). INSTALLING AN INTEGRAL BLOWER THE VTN30Q blower may be mounted prior to or after range installation depending on duct and taping variables. The integral blower housing inlet (See Figure 15) fits over the plenum outlet ring (Figure 14), and is secured to the plenum with a blower mounting bracket. The blower may be rotated in various directions to achieve right side, left side, rear or floor venting. See pages 10 to 12 for specific installation steps. Threaded rods included in the blower kit will be secured to the mounting nuts "A" or "B" shown in Figure 15. Further installation instructions are specified in the following sections. Figure 14 ­ Bottom View of Exhaust plenum Up Front B A Plenum Exhaust Outlet B A Figure 15 ­ Integral Blower Vent to Side Back and Floor FFO FF O FF O Blower Inlet Threaded Rods Mounting Bracket 9 I VENTILATION INTEGRAL BLOWER - RIGHT OR LEFT DUCTING 1. Determine blower direction and cutout in cabinet as shown in Figs. Remove the existing 1/4 ­ 20 screws from either positions "A" or "B" and discard them. [. . . ] Length = 2 Ft. Integral Blower 90° Through Floor Model #STL90R Equiv. Length included in Chart 2 Model #I 40 Model #RJ310 Equiv. 5 Ft. 7" In-Line Backdraft Damper (not shown) 3-1/4" x 10" Roof Jack and Shutter (not shown) NOTE: Fittings with model numbers stated are available through your Thermador dealer. All other fittings are available from any major hardware store. 17 Straight Length 6 Ft. [. . . ]