User manual THETA DIGITAL CB II RS232 PROTOCOL

[. . . ] The duration of a single bit is equal to 1 / baud rate. Echo status: Specifies a "status level" to return to controlling device upon any operating change in Casablanca II. level 1 will return current mode, input, master level. [. . . ] All values below in decimal unless otherwise noted (h) or (hex). 2 Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Command 1 Description Variable Change Argument 1 Argument 1 Description 0-255 Variable Number (see status levels) . 3 Update Display 1 2 3 4 Menu LEDs Menu Parameters Menu Display Re-display whole menu Argument 2 3=internal, 1=global, 0=by input Argument 2 Desc Argument 3 Arg 3 Desc Location Of 0-255 new value Variable 4 Do Action 5 6 Select Input User Mute 1-12 0 1 2 0-255 0-255 0 1-6 0 1 2 15 17 Power remote Mode select (Note: If in input select menu, this command should be followed by "03 04 00 00" to update the display. ) 0 0 1 2 3 4 5 8 9 10 11 3=internal, 1=global, 0=by input 3=internal, 1=global, 0=by input Input number. Matrix Special matrix Pro Logic Dolby Digital DTS Stereo Mono CS encoded CS non-encoded CS Cinema location of variable 0-255 From this doc. location of variable 0-255 From this doc. 8 9 12 14 Go To Menu Go To Menu W/Password Check Source change. Power main. time at new menu time at new menu 20 21 Variable, Specified, Increment Variable, Specified, Decrement 3 Variable Number Variable Number Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Command Description Argument 1 26 29 36 51 52 Argument 1 Description Variable, Input, Set Value Variable, Internal, Set Value Return To Previous Menu Variable, Selected, Increment Variable, Selected, Decrement Argument 2 0-255 0-255 0-4 Argument 2 Desc Argument 3 Arg 3 Desc Variable Number 0-255 New Value Variable Number 0-255 New Value # of menus to go back 5 6 7 8 9 Get variable value Return status Write LCD buffer address Write char to LCD buffer. Write OSD buffer address. 0-255 0-4 0-39d 0-7F 0-1 Variable Number (see status levels) Return specified status level. Character Address high byte 3=internal, 1=global, 0=by input Location of Variable 0-7F (FF skips char) Character 0-255 Address low byte 10 11 Write chars to OSD buffer. 0-7F Simulate Keypress 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Character None 1 2 3 4 5 6 A/D Mute Mode Tape Out Setup Balance Display IR Power Main Up Down Power Remote Status Left Right Phase Select Up 4 0-7F (FF skips char) Character 0-7F Addr high: Addr low <308 0-7F Character Character Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Command Description Argument 1 23 24 25 26 Argument 1 Description Select Down EQ Power Standby Power Activate Argument 2 Argument 2 Desc Argument 3 Arg 3 Desc 12 14 15 16 17 18 19 Read Serial Number ** See note #4 Read Display Type ** See note #6 Read Configuration ** See note #7 Go to sys util Return OS version do not use Read Parameter LCD ** 0-255 See note#1 Read Parameter OSD ** See note#1 Write Parameter LCD ** See note#2 Write Parameter OSD ** See note#2 Read Variable Range ** See note #1 0-255 Parameter Number, From Include File 0-255 Parameter Offset Value Parameter Offset Value Parameter Offset Value Parameter Offset Value 2<x<255 20 Parameter Number, From Include File 0-255 2<x<65 21 0-255 Parameter Number, From Include File 0-255 2<x<101 22 0-255 Parameter Number, From Include File 0-255 2<x<65 23 24 25 3=internal, 1 Variable Location =global, 0=by input Write Variable Range ** 3=internal, 1 Variable Location See note #2 =global, 0=by input Execute Macro ** See note 0 Copy Current Input Settings #3 1 Copy Current Speaker Settings 2 Restore factory default settings 0-255 Variable Number 2<x<255 to start reading at Variable Number to start writing at Input to copy to Input to copy to To Current Input To All Inputs To Global Settings To Input and Jack Names To Everything 2<x<101 0-255 Number Of Bytes To Read Number Of Bytes To Read Number Of Bytes To Write Number Of Bytes To Write Number of bytes to read Number of bytes to write 1-12 1-12 0 1 2 3 4 5 Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details ** Note 1: After sending command, Casablanca will return number of bytes requested followed by an 8 bit checksum byte (not two's complement right now). ** Note 2: After sending command, wait for Casablanca to return checksum of arg1+arg2+arg3 (not 2's complement) , then send # of bytes specified in command (do not follow with checksum yet);CB will return checksum of received bytes to write (not 2's complement). ** Note 3: Casablanca will return "01" upon completion of the macro. All macro commands should be followed with a "Go To Menu" command, with the desired menu number as argument 1. This is because macros internally alter the current menu number. ** Note 4: After sending command Casablanca, Casablanca will return 6 ASCII bytes representing the serial number. ** Note 6: After sending command Casablanca, Casablanca will return 4 ASCII bytes representing the display type (VFD ) or (LCD ). ** Note 7: After sending command Casablanca, Casablanca will return 75 bytes plus a checksum. Status Levels: The RS232 can be set to automatically send changes to the RS232 port. [. . . ] RECEIVING_DOLBY_DIGITAL RECEIVING_DTS STATUS RS232 OPTION_NOT_INSTALLED PHASE SETUP_INPUT_POST_PROCESS THETA_DIGITAL SETUP_DOLBY_DIGITAL_2 MACROS_1_2 SETUP_NAMES_DIGITAL_COAX SETUP_INPUT_JACK_NAMES SETUP_NAMES_DIGITAL_MISC_1 SETUP_ANALOG_INPUT_LEVELS SETUP_NAMES_ANALOG BALANCE_1 BALANCE_2 SETUP_NAMES_VIDEO_1 SYSTEM_CONFIG CONFIG_LEFT_RIGHT_PHASE_PERFECT CONFIG_LEFT_RIGHT_LINKWITZ_RILEY CONFIG_LEFT_RIGHT_BUTTERWORTH 18 Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Menu # 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 Parameter # 0 1 2 3 4 5 6 7 8 9 10 11 Menu Description CONFIG_CENTER_PHASE_PERFECT CONFIG_CENTER_LINKWITZ_RILEY CONFIG_CENTER_BUTTERWORTH CONFIG_SURROUNDS_PHASE_PERFECT CONFIG_SURROUNDS_LINKWITZ_RILEY CONFIG_SURROUNDS_BUTTERWORTH RS232_USER_CONFIGURABLE MODE_3 SIGNAL_GENERATOR SETUP_MUTE_VOLUME SETUP_NAMES_DIGITAL_MISC_2 LEVELS_MAIN LEVELS_2 LIST_INSTALLED_BOARDS DELAYS_2 PASSWORD_ENTER SETUP_STATUS_DISPLAY_2 SETUP_GLOBAL_2 SETUP_INPUT_CONFIG_SURR_CEN CONFIG_SURRC_PHASE_PERFECT CONFIG_SURRC_LINKWITZ_RILEY CONFIG_SURRC_BUTTERWORTH MACROS_INPUT MACROS_SPEAKER MACROS_FACTORY SETUP_NAMES_VIDEO_2 Parameter Description EQ_LIST MODE MUTED_LEVEL TAPE_DA INPUT_NAMES_RESTORE SLOPES DIALOG_NORMALIZATION_LIST CROSSOVER_CONFIGURATION REMOTE_POWER_SOURCES CROSSOVER_FREQUENCIES CROSSOVER_TYPES REMOTE_POWER_TYPES 19 Rev 0. 5 2/15/04 Parameters Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Parameter # 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Parameter Description SUBS_CONFIGURATION LEVEL_MUTED AC3_CHANNELS PHASE PHASE_LIST AD_DISPLAY_OSD COPYRIGHT PAL_NTSC AC3_BITSTREAM_MODE OFF_ON DOLBY_2CH_LCD CENTER_LOPASS_TO_LIST NOISE AC3_SAMPLE_RATES AC3_DATARATES AC3_LFE_STATUS INPUT_NAMES_ALTERABLE AC3_SURROUND_MODE PASSWORDS INPUT_JACKS_ALTERABLE INPUT_JACKS_RESTORE OSD_BACKGROUND_COLOR LFE_GAIN_LIST_DD LCD_OSD AC3_CENTER_MIX_LEVELS AC3_SURROUND_MIX_LEVELS AC3_COPYRIGHT AC3_ROOM_TYPES BCD_255 IN_JACKS_VIDEO_ALTERABLE IN_JACKS_VIDEO_RESTORE SUBCEN_SURCEN SYS_DIG_CHS MODES_SHORT BAUD_RATES BCD NARROW_WIDE ALL_ONE ANALOG_LEVEL_LIST 20 Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details Parameter # 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Parameter Description BALANCE_GRAPHICS BALANCE_NUMERIC LEVEL_GRAPHIC BALANCE_SUBS_CENTER BCD_PLUS_MINUS STATUS_PARAMETERS SLOPES_LR RS232_ECHO_STATUS SERIAL_NUMBER LEVEL_INITIAL_CONFIG MUTE_TRIGGERS SAMPLE_RATES SUBS_NUMBER CURSOR_TYPES LEVEL_LIST_PHANTOM SYS_DIG_OPT SYS_FRCEN_FRSUB SYS_SUB4_SUB5 SPEAKER_NAMES CONFIG_MENU_PARAMS MORE_MENU LIST_INSTALLED_BOARDS NOT_INSTALLED CHANNELS SIGNAL_TYPES SIGNAL_LEVELS SIGNAL_FREQUENCIES DISPLAY_BRIGHTNESS TAPE_MENU_OPTION TAPE_MENU_MESSAGE 21 Rev 0. 5 2/15/04 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details The command to request a status level is 06 0x 00 00, where x= the status level. When this command is issued, there is a 6. 7mS delay before the first status byte is received. The ECHOS parameter in the Casablanca II determines what status levels of data are returned. The diagram below shows all 4 status levels returned and the delay times between them. [. . . ]