User manual THETA DIGITAL CB3REVBRS232PROTOMAD1.01

[. . . ] The duration of a single bit is equal to 1 / baud rate. Echo status: Specifies a "status level" to return to controlling device upon any operating change in Casablanca III. level 1 will return current mode, input, master level. [. . . ] To set a specific master volume level from any menu: <header> 1 9 3 x, where x = the volume level [0 -73] (values are decimal). 2 Rev 1. 01 11/9/05 Casablanca III Owners Manual Addendum RS232 Protocol and Control Details This document is divided into several sections to facilitate ease of use when looking up values. There is a separate chart for Input Variables, or variables for parameters that are stored by Input. There is another chart for Global Variables. As such there are tables for Status levels, Menus, Character Maps and other Parameters. Below are some examples of using the command format. These examples will show how and where to look up values. Example 1: To Take the Casablanca III out of standby: Header 254 236 Command 4 Argument 1 14 Argument 2 2 Argument 3 0 All entries from this command string were obtained from the Command List on page 5 of this document. Example 2: To select Input # 3: Header 254 236 Command 4 Argument 1 5 Argument 2 3 Argument 3 0 -All entries from this command string were obtained from the Command List on page 5 of this document. Example 3: To change the front center level to +2, for the currently selected input: Header 254 236 Command 1 Argument 1 37 Argument 2 0 Argument 3 2 -Command 1 is used because it is required to change a parameter that is not already listed under the "commands and argument 1's on the Command List. -Argument 1's value was found on the Input Variables chart, as indicated under the "Argument 1 description". -The Argument 2 was used because this is an Input variable. a parameter that is stored "by Input" -Argument 3's value is the "new value" that is desired for the parameter being edited. Example 4: To change the analog tape out source to the coax 3 input jack: Header 254 236 Command 1 Argument 1 3 Argument 2 1 Argument 3 9 -Command 1 is used because it is required to change a parameter that is not already listed under the "commands and argument 1's on the Command List. -Argument 1's value was found on the Global Variables chart, as indicated under the "Argument 1 description". -The Argument 2 was used because this is an Global variable. a parameter that is NOT stored "by Input" -Argument 3's value is the "new value" that is desired for the parameter being edited. In the case of Jack names/variable numbers, this data was found on the Jack Variable chart. 3 Rev 1. 01 11/9/05 Casablanca III Owners Manual Addendum RS232 Protocol and Control Details ­ Command List Command 1 1 3 Description Input Variable Change Global Variable Change Update Display Argument 1 0-255 0-255 1 2 3 4 Argument 1 Description Variable Number (see Input Variables chart) Variable Number (see Global Variables chart) Menu LEDs Menu Parameters Menu Display Re-display whole menu Argument 2 Argument 2 Desc 0 Input setting 1 Global setting 0 0 0 0 Argument 3 0-255 0-255 0 0 0 0 Arg 3 Desc New value New value 4 Do Action 5 6 Select Input User Mute 1-12 0 1 2 0-255 0-255 0 1-6 0 1 2 0 0 1 4 5 6 7 8 9 10 11 12 13 14 15 0 1 Input number. Matrix Special Matrix Stereo Analog Direct Analog Matrix Mono Circle II Cinema Circle II Music Circle II Mono Matrix Pro Logic IIx Movie Pro Logic IIx Music Pro Logic IIx Mono Mx DTS NEO:6 Cinema DTS NEO:6 Music Input setting Global setting 0 0 0 0 0-255 0-255 8 9 12 14 Go To Menu Go To Menu W/Password Check Source change. Power main. time at new menu time at new menu 15 17 Power remote Mode select (Note: If in input select menu, this command should be followed by "03 04 00 00" to update the display. ) 20 20 Input Variable, Specified, Increment Global Variable Specified, Increment 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-255 From Input Variable Variable chart. Number 0-255 From Global Variable Variable chart Number Rev 1. 01 11/9/05 Casablanca III Owners Manual Addendum RS232 Protocol and Control Details ­ Command List Command Description Argument 1 Argument 1 Description 20 Internal Variable Specified, Increment 21 Internal Variable Specified, Decrement 21 21 26 36 Global Variable Specified, Decrement Internal Variable Specified, Decrement Variable, Input, Set Value Return To Previous Menu Argument 2 Argument 2 Desc 3 Internal setting 0 Input setting 1 3 0-255 0-4 Global setting Internal setting Argument 3 Arg 3 Desc 9 Master Volume 0-255 From Input Variable variable chart. [. . . ] This is because macros internally alter the current menu number. 6 Rev 1. 01 11/9/05 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details ­ Input Variable Chart Input Variables: Variable # 0 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Variable Name CENTER_CONFIG LR_BW_LOP_FREQ CEN_PF_FREQ CEN_PF_SLOPE CEN_PF_LOP_PHASE CEN_BW_HIP_SLOPE CEN_BW_HIP_FREQ CENTER_LOPASS_TO LR_CONFIG CENTER_TYPE LR_PF_FREQ LR_PF_SLOPE LR_PF_LOP_PHASE LR_BW_HIP_SLOPE LR_BW_HIP_FREQ SUR_CONFIG SUR_PF_FREQ SUR_PF_SLOPE LR_LR_SLOPE SUR_PF_LOP_PHASE LR_LR_LOP_PHASE SUR_BW_HIP_SLOPE SUR_BW_HIP_FREQ DELAY_LEFT DELAY_REAR_LEFT DELAY_REAR_RIGHT DELAY_CENTER DELAY_RIGHT DELAY_SUB_1 CEN_BW_LOP_FREQ CEN_BW_LOP_SLOPE CEN_BW_LOP_PHASE CEN_LR_FREQ CEN_LR_SLOPE DD_ADD_SPKRS Variable # 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 Variable Name LEVEL_LEFT LEVEL_CENTER LEVEL_RIGHT LEVEL_REAR_LEFT LEVEL_REAR_RIGHT LEVEL_SUB_1 SEARCH_6_VIDEO LEVEL_PHTM_SUR DTS_ADD_SPKRS PL2X_PANORAMA PL2X_CTR_WIDTH NEO6_CTR_GAIN SIX_SHOOTER CS_DELAY_CENTER CS_LEVEL_CENTER CS_DELAY_SUR CS_LEVEL_SUR DD_2CH_MODE_ENC DD_COMPRESSION DD_COMP_HIGH DD_COMP_LOW DD_DIALOG_NORM DD_LFE_GAIN DD_DELAY_CENTER DD_LEVEL_CENTER SUB2_FULL_XOVER DD_LEVEL_SUR DTS_LFE_GAIN DTS_DELAY_CENTER DTS_LEVEL_CENTER DTS_DELAY_SUR DTS_LEVEL_SUR MODE_DEFAULT CEN_LR_LOP_PHASE LFE_PHASE Variable # 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 Variable Name SUB3_FULL_XOVER SEARCH_1 SEARCH_2 SEARCH_3 SEARCH_4 SEARCH_5 SEARCH_6 CS_DLG_CLARITY CS_CLARITY_LVL DD_EX_DECODE (+SPKR) VFD_BRIGHTNESS NAME_VFD NAME_OSD OSD_BACKGROUND_COLOR OSD_LEFT_EDGE OSD_TOP_EDGE OSD_CONFIG OSD_DISPLAY_TIME STATUS_MODE STATUS_INPUT STATUS_TAPE STATUS_LEVEL STATUS_EQ STATUS_PHASE STATUS_SOURCE LR_LR_FREQ POST_PROCESS LR_BW_LOP_SLOPE SUBS_NUMBER SUB1_FULL_XOVER SEARCH_1_VIDEO SEARCH_2_VIDEO SEARCH_4_VIDEO SEARCH_3_VIDEO SEARCH_5_VIDEO 7 Rev 1. 01 11/9/05 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details ­ Input Variable Chart Variable # 106 107 108 109 110 111 112 113 114 116 117 119 120 122 123 124 125 126 127 128 129 130 131 132 133 Variable Name LR_BW_LOP_PHASE SOURCE_NOISE1_NOISEALL SUR_BW_LOP_FREQ SUR_BW_LOP_SLOPE SUR_BW_LOP_PHASE SUR_LR_FREQ SUR_LR_SLOPE SUR_LR_LOP_PHASE SUB4_FULL_XOVER CENTER_SPREAD DD_DELAY_SURROUND SIDE_CONFIG SURROUND_CENTER LR_TYPE SURROUND_TYPE LEVEL_SIDE_LEFT LEVEL_SIDE_RIGHT LEVEL_REAR_CENTER or SUB5 LEVEL_SUB_2 LEVEL_SUB_3 LEVEL_SUB_4 DELAY_REAR_CENTER or SUB 5 DELAY_SIDE_LEFT DELAY_SIDE_RIGHT DELAY_SUB_2 Variable # 134 135 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 156 157 158 159 160 Variable Name DELAY_SUB_3 DELAY_SUB_4 STATUS_SAMPLE_RATE JACK_SEARCH DELAY_MASTER DD_2CH_MODE_NENC SURC_CONFIG SURC_BW_HIP_FREQ SURC_BW_HIP_SLOPE SURC_BW_LOP_FREQ SURC_BW_LOP_SLOPE SURC_BW_LOP_PHASE SURC_LR_FREQ SURC_LR_LOP_PHASE SURC_LR_SLOPE SURC_PF_FREQ SURC_PF_LOP_PHASE SURC_PF_SLOPE SURC_TYPE LEVEL_PHTM_FRONT_CENTER LEVEL_PHTM_SUR_CENTER SUB5_FULL_XOVER LEVEL_SUB_5 DELAY_SUB_5 8 Rev 1. 01 11/9/05 Casablanca II Owners Manual Addendum RS232 Protocol and Control Details ­ Global Variable Chart Global Variables: Variable # Variable Name 0 TAPE_FOLLOW_INP 1 BALANCE_CLEAR 2 BALANCE_ANALOG_INPUT_LEVEL 3 ANALOG_TAPE_OUT 5 LEVEL_MASTER_INITIAL 6 PHASE 7 BALANCE_EQ 8 MAIN_TIME 9 CURSOR_VFD 11 MAIN1_TYPE 13 VOLUME_FAST 14 MAIN2_TYPE 15 LEVEL_MAX 16 TAPE_DIGITAL_SOURCE 17 REMOTE_PULSE_DURATION 18 TAPE_OUT_DIGITAL 19 TAPE_OUT_VIDEO 20 MUTE_LEVEL 21 MUTE_TRIGGER Variable # 22 24 27 32 33 34 35 36 37 38 39 40 41 42 43 44 45 50 57 Variable Name RS232_BAUD_RATE RS232_ECHO_STATUS VOLUME_SLOW MAIN_OFF_SEQUENCE REMOTE_TYPE MAIN3_TYPE BALANCE_L_R BALANCE_F_R BALANCE_CENTER BALANCE_SUBS ANALOG_TAPE_OUT ANALOG_LEVEL_1 ANALOG_LEVEL_2 ANALOG_LEVEL_3 ANALOG_LEVEL_4 ANALOG_LEVEL_5 ANALOG_LEVEL_6 MSG_MODE IDLE_TIMEOUT 9 Rev 1. 01 11/9/05 Casablanca III Owners Manual Addendum RS232 Protocol and Control Details ­ Status Levels Chart Status Levels: The RS232 can be set to automatically send changes to the RS232 port. When this command is issued, there is a 6. 7mS delay before the first status byte is received. The ECHOS parameter in the Casablanca III determines what status levels of data are returned. The diagram below shows all 4 status' levels returned and the delay times between them. [. . . ]