User manual THOMSON VTH6081U

[. . . ] . GB . Important Précau tions e Somma ire 1 INSTAL LATION confor - Assur me appare à celle indiqu ez-vous que il. chaleu Installez le ée sur l'étiqu la tension-sect r magné importante magnétoscop ette d'identificati eur de votre tiques e habita à la chaleu ou électri(cheminée. . . horizontalem on, située à l'arrièr tion est ) ou ques ent, r. La Celsiu tempé élevés. [. . . ] With MENU (15) key, call up the SUMMARY menu. With w (11) key select the Installation line and confirm with OK (13). With w (11) key select the Satellite and cable box line and confirm with OK (13). Select the country where you live or the country from which you wish to receive the channels, in the case of living on the border, from the list of countries which appears on the screen and press OK (13). " The SATELLITE AND CABLE screen appears. 7 With C (12) or B (10) keys, select the socket to which your satellite receiver is connected: - either RF or Coax (mono sound); validate with OK (13). The satellite receiver communication channel search screen appears; press C (12) or B (10) to start the search, then validate with OK (13) on completion of the search. - either AV1 or AV2 and validate with OK (13), then select No decoder (the other options are rarely used in Europe) and revalidate with OK (13). 8 Enter your satellite code number (see the code table at the end of this user manual), then validate with OK (13). GB If the make or model of your satellite/cable receiver is not on the list, try out other model numbers. If no code works, repeat the procedure described on this page by entering the 00; the video recorder then tries out all the codes stored in its memory. " Via the infrared window, the video recorder transmits a signal to your satellite receiver. A confirmation menu comes up while the satellite receiver positions itself on channel 12 (check whether channel 12 is indicated by the display on satellite receiver occasionally in a slow manner -, even if there is no image to be seen on the television screen). 9 Should the satellite receiver not use channel 12, select NO with the EXIT (14) key. Your video recorder then starts a new search (depending on the make of your satellite receiver, several attempts are possible). 10 If the satellite receiver uses the channel 12, select YES with the OK (13) key. Wait for quite a long time (up to 15 minutes) until a message tells you that the storage of your satellite channels is completed. " Your video recorder now controls your satellite receiver. 13 Refer to page 5 to sort your satellite channels and check their names. If you should wish to change your satellite receiver, select the Installation line from the SUMMARY menu then the Satellite and cable line and finally the New installation line. If you should wish to rearrange your satellite receiver channels, select the Satellite channel identification line from the SATELLITE AND CABLE menu. connecting the recorder to a Whenselect the socket videoduring set-up. television set with integrated satellite receiver, you must AV1 7 Installation Other sets Press the STATUS key (6) to call up the control screen and select the socket AV1, AV2, AV3 or AV4 with key AV (23) of the remote control. Sockets AV1 / AV2 / AV3 / AV4 AV1 - AV2 AV2 Decoder AV1 / AV2 / AV4 DVD Other video recorder AV4 Camcorder Audio/Video or Dolby Pro Logic amplifier The four cinch sockets AUDIO IN/OUT (red and white) and the two VIDEO IN/OUT cinch sockets (yellow) enable you to connect your video recorder to an Audio/Video amplifier. TV set Satellite receiver Video disk player The pictures from another set operating in the play mode and connected to AV2 are conveyed to the socket AV1. When your television is connected to this socket, you can watch the pictures from the set connected. AV3 Hi-Fi system Camcorder Connect your camcorder to the sockets AUDIO L (left), AUDIO R (right), VIDEO IN and CAM/PAUSE and select socket AV3 on your video recorder. The four cinch sockets AUDIO IN/OUT (red and white) enable you to connect your video recorder to the HiFi stereophonic system. [. . . ] Fast forward the tape to the end of the sequence to be replaced and press STOP (27). Press 0000 (21) key to reset the counter. Rewind the tape to the beginning of the sequence to be replaced and press PAUSE (28) key. Press on REC (29) and finally start playing from the source so as to begin the insertion. [. . . ]