User manual TISSOT FLY-BACK CHRONOGRAPHS

[. . . ] When operating as a chronograph, this model is able to time events lasting up to 30 minutes, displaying the results to the 1/10th of a second, and also provides you with the following functions : ­ Standard START­STOP function ­ ADD function (partial times) ­ SPLIT function (intermediate times) ­ FLY-BACK function To ensure that your chronograph operates with perfect precision for many years to come, we advise you to pay very careful attention to the advice provided hereafter. This user's manual is applicable to all TISSOT ® quartz chronographs with FLY-BACK function. Usage / Settings Models with a screwed crown You must first unscrew the crown into position IB before you can pull it out into position II or III. Important : After each operation, you must always screw the crown back down to ensure that your watch remains water-resistant. Pushers Press briefly on the pusher to move the hands in increments. [. . . ] ­ Then, press the crown back into position I (and tighten it down if you have a model with a screwed crown). Note : Rapid synchronization (particularly useful when changing time zones) by + or - 1 hour can be carried out using both pushers D and C. Important : Before synchronizing the watch, check that hands (3) and (4) and counter hands (6) and (7) are at position 0 (at 12 o'clock) with the crown pulled to position II (see Setting the counters to zero). 1 8 Alarm 7 1 4 D A 2 3 B 3 Crown in position I Select the « Set Alarm » mode. Exit the « Set Alarm » mode. Notes : The 30 minute counter hand is set at the « Set Alarm » position. When the alarm time is set, the alarm is activated (ON). Your watch will exit the « Set Alarm » mode if no settings are made within 15 seconds. The red hand (3) always shows the alarm time and the 1/10 second counter hand (7) indicates whether the alarm is switched on. Crown in position I B Ringing test C ON/OFF (activated/deactivated) Notes : An audible signal indicates that the alarm is switched on (ON). The ringing can be stopped by pressing any pusher. These functions are not available if the chronograph is running or on hold. C B Chronograph (simple function) A 1 2 The simple « chronograph function » enables you to measure isolated events. Crown in position I START/STOP STOP Reading the time Reset counters to zero B 3 Notes : The 60 second, chrono and 30 minute hands return to 0 for all chronograph functions, while the 1/10 second counter hand shows the alarm status (ON/OFF). 4 3 2 1 Chronograph (ADD function) The ADD function enables you to measure consecutive events without having to reset to zero between each event. Each time recorded is simply added to the previous total. Crown in position I START STOP Reading the time RESTART STOP Reading the time Reset counters to zero A B 5 w w w. ch 3/4 125_EN / 08. 06 Fly-Back Chronographs * Chronograph (SPLIT function) A 1 4 The SPLIT-TIME function enables you to stop the hands to read an intermediate time, without interrupting the timing operation. When you restart, the hands « catch up » the lost time. Crown in position I START SPLIT Reading the time X RESTART (catchup) STOP Reading the last time Reset counters to zero B 2 3 5 A 1 3 Chronograph (double chrono) This function allows you to time two events simultaneously. Crown in position I START (T1, T2) SPLIT Reading the time T1 STOP T2 (memorizes T2) Reading the time T2 Reset counters to zero B 2 4 5 Chronograph (FLY-BACK function) A 1 3 The FLY-BACK function can be activated while timing. The 30 minute, 60 second, chrono and 1/10 second counter hands are reset and a new timing function starts automatically. [. . . ] Type : High impedance / SR 936 PW / Renata 380. Collection and treatment of end of life quartz watches* This symbol indicates that this product should not be disposed with household waste. It has to be returned to a local authorized collection system. By following this procedure you will contribute to the protection of the environment and human health. [. . . ]