User manual TISSOT T-TOUCH

[. . . ] It is not advisable to press the pushers while the watch is submerged. None of the functions can be activated if the crystal is in contact with a liquid. General information on use · Activate the crystal by pressing · When the crystal is activated, a flashing bar will appear on the digital display · Select a function by touching the corresponding area on the crystal · Brief pressures on the pushers = step by step movement of the hands or incrementation (decrementation) on the digital display · Long pressures on the pushers = continuous movement or incrementation (decrementation) · Incorrect operation of the pushers = different alarm signal from the normal beep · No operation for 30 seconds = automatic deactivation of the crystal · No operation for 3 seconds in setting mode = exit from setting mode. www. tissot. ch 2/14 138_en / 01. 07 Use: Adjustment: Touching action (without pressing) Beep Listening / Vision Time for pressing on the pushers (e. 2 seconds) Additional information Repetitive actions Hand position display Care and maintenance We recommend that you clean your watch regularly using a soft cloth and lukewarm water. After bathing in salt water, rinse your watch with fresh water and leave it to dry completely. [. . . ] (2) After 30 seconds, the hands display the time again but the digital display remains in CHRONO mode. After 10 h, the digital display returns to "h-m-s" mode. CHRONO (split) 1" Precise measurement of a specific duration with intermediate time Activation of the crystal Activation of the chronograph Starting the chronograph Displaying the intermediate time (eg. 48'' and 15/100) Restarting the chronograph, taking into account the running time Stopping the chronograph (eg. 2' 54'' and 88/100) Resetting the chronograph 138_en / 01. 07 7/14 www. tissot. ch Compass Indication of the geographical north COMPASS 1" N Activation of the crystal Activation of the compass function(1) S 2" Activation of the adjustment of the magnetic variation(2) + or - 1 degree Setting the magnetic variation to the east (+) or west (-) Validation of the setting (eg. 2° East) (1) The minute hand points to the North. A more accurate reading is obtained by holding the T-Touch horizontally. The digital display gives the set magnetic variation. After 30 seconds, the digital display returns to "h-m-s" mode. (2) For more information, see the explanation of the magnetic variation on page 11. ALARM 1" Activation of the crystal Activation of the alarm function (eg. 12h19') 1" Activation of the alarm Deactivation of the alarm Setting the time + or - 1 minute Incrementation or decrementation by one minute Validation of the setting (1) When the programmed time is reached, the alarm can be stopped by pressing one of the pushers. www. tissot. ch 8/14 138_en / 01. 07 2" ALTIMETER Indication of altitude in relation to sea level 1" Activation of the crystal Activation of the altimeter function(1) 2" + or - 1 step Adjusting the altitude(2) Incrementation or decrementation (1 m or 3 ft) Validation of the setting (1) The altitude is displayed in metres or feet depending on the units selection (see "Selecting the units" on page 6). After 30 seconds, the hands show the time again but the digital display remains in ALTIMETER mode. After 10 h, the digital display returns to "h-m-s" mode (2) The adjustment shows the altimeter setting at the value of the actual altitude. For more information, see the explanation of the altimeter on page 12. THERMO 1" Indication of the temperature(1) Activation of the crystal Activation of the thermometer function (1) To obtain the best reading, it is necessary to remove the watch from your wrist and wait for approximately 15 to 30 minutes. For more information, see the explanation of the thermometer on page 13. (2) The temperature is displayed in degrees Celsius or in degrees Fahrenheit depending on the units selected (see "selecting the units" on page 6). After 30 seconds, the hands display the time again but the digital display remains in THERMO mode. 138_en / 01. 07 9/14 www. tissot. ch Glossary METEO Indication of the meteorological trend Description of the function In METEO mode, the watch hands are superposed to indicate the meteorological trend. Explanations Changes in weather are linked to variations in atmospheric pressure. The T-Touch watch measures these pressure variations and indicates the meteorological trend for the coming 24 hours. When atmospheric pressure increases, the sky clears. [. . . ] The value of the magnetic variation therefore also depends on the date. When the correct value (depending on place and date) of the magnetic variation is set (see the adjustment procedure on page 8), the minute hand on your T-Touch displays the direction of the geographical North (Ng). The values and dates of the magnetic variation are displayed on topographical maps or can be searched for using special software available on Internet. Ng Nm Miscellaneous information If you set the magnetic variation to 0, your T-Touch will display the magnetic North (Nm). The COMPASS function, as any other compass, must not be used near a metal or magnetic object. 30° 15° Thanks to its rotating bezel, you can use the compass of your T-Touch watch to orient a map. [. . . ]