User manual TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497. We hope that this TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497 user guide will be useful to you.

Lastmanuals help download the user guide TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497.

Mode d'emploi TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497

Download

Manual abstract: user guide TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497

Detailed instructions for use are in the User's Guide.

 [. . . ] TJERNLUND PRODUCTS,  INC. 
1601 Ninth Street · White Bear Lake,  MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com

PAI-G/GT/O SERIES REPLACEMENT FAN PROVER SWITCH INSTALLATION INSTRUCTIONS
OWNERS INSTRUCTIONS THESE INSTRUCTIONS MUST REMAIN WITH EQUIPMENT DO NOT DESTROY ALWAYS FOLLOW HEATER MANUFACTURER'S INSTRUCTIONS FOR PROPER OPERATION OF HEATER AND RE-LIGHTING OF PILOT

READ INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION

1. Disconnect electrical power before making wiring connections to prevent electrical shock and equipment damage. All wiring must comply with applicable codes and ordinances.  [. . . ] Bend of actuating wire should be pointed away from damper as shown. Push female leads on new Proving Switch. Wire leads on switch should point in direction they enter damper cavity. The BLUE wire from IN-FORCER junction box should be connected to the COM terminal of Proving Switch and the YELLOW wire should be connected to N/O terminal of Proving Switch. Reinstall PAI Proving Switch assembly to damper assembly with (2) nuts. Before reassembling IN-FORCER,  check Proving Switch for free movement. Proper operation of Proving Switch can be verified by a "click" sound as switch opens and closes. Follow reverse procedure in steps 1 & 2 to reassemble IN-FORCER. Verify proper heater and IN-FORCER operation. 

DIAGRAM A

1. Disconnect electrical power before making wiring connections to prevent electrical shock and equipment damage. All wiring must comply with applicable codes and ordinances. When wiring is completed,  check all components by running system through its entire heating cycle. IN-FORCERS with date codes after "9704" For the steps following below,  refer to diagram B. Remove (6) screws from bottom front and sides of IN-FORCER while holding blower assembly firmly. Carefully slide blower assembly down until stops,  hold it in place. Carefully remove BLUE & YELLOW leads from Proving Switch.  [. . . ] Follow reverse procedure in steps 1 & 2 to reassemble IN-FORCER. Verify proper heater and IN-FORCER operation. DIAGRAM B

P/N: 8504044

©1997 TJERNLUND PRODUCTS,  INC.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-0452 PAI-1,2 PROVER KIT 8504044 REV. 1 0497 will begin.