User manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199. We hope that this TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199 user guide will be useful to you.
Lastmanuals help download the user guide TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199.
Manual abstract: user guide TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
Detailed instructions for use are in the User's Guide.
[. . . ] It is necessary to replace the entire Plenum Section part # 950-0670 which includes the motor and electrical controls. SideShots with date codes after "9518", (gray MAGNETEK motor with 2 wire leads) For the steps following below, refer to diagram A. Remove electrical box cover and disconnect (2) motor leads. Remove and save (1) motor bracket screw from electrical box. [. . . ] Remove and save (2) nuts from inlet collar on housing inside plenum. Note: Removal of plenum access cover plate will allow for removal of inlet collar nuts with 11/32" box end wrench. Push down electrical box about 1/4" so motor mount plate can clear junction box. Once motor mount plate has cleared the studs it can be rotated so motor mount plate flat aligns up with junction box for easier removal. Holding the motor, apply firm pressure towards the plenum of the SideShot and remove and save the (6) motor mount nuts. Note: An 11/32" box end wrench is used for nut directly under electrical box. Note: Hold the assembly firmly; failure to do so could damage internal parts.
DIAGRAM B
4.
5.
6.
Slide motor/wheel assembly from Plenum. Grasp only the motor casing; do not damage wheel, shaft or other components on Plenum. Do not rest assembly on wheel.
For the steps following below, refer to diagram C. Loosen set screw from wheel hub with 5/32" allen wrench. Twist wheel to loosen and pull off of motor shaft. Wheels "fused" to shaft may require penetrating oil and/or a wheel puller to facilitate removal. Important: The housing inlet collar from old motor will have to be removed and saved for use with the new motor.
DIAGRAM C
For the steps following below, refer to diagram D. The new motor/wheel with spring ring inlet collar assembly is only compatible with SideShots with date codes after 9518. The following modifications will have to be made to adapt the motor/wheel assembly to the SideShot with date codes between 9226 and 9517. Loosen set screw with 5/32" allen wrench and remove wheel from new motor.
DIAGRAM D
10. Remove and save (4) nuts from the new motor mounting plate and remove from motor. Remove (2) screws which hold spring ring inlet collar assembly to mounting plate and discard spring ring inlet collar assembly. Secure motor to mounting plate with (4) nuts removed in step 10. Important: The capacitor of the motor should be opposite the flat edge on motor mounting plate. [. . . ] Route BLACK and WHITE wires from motor into electrical box . Note: A ground wire is not included on these replacement motors. The motor is grounded by contact with the Plenum and ground wire from terminal strip to Plenum. Remove 1/4" of insulation from the WHITE wire of motor and connect to "L2" of terminal strip. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-0625 SS1 MOTOR KIT 8504016 REV. A 1199 will begin.
