User manual TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196. We hope that this TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196 user guide will be useful to you.
Lastmanuals help download the user guide TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196.
Manual abstract: user guide TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196
Detailed instructions for use are in the User's Guide.
[. . . ] When wiring is completed, check all components by running system through its entire heating cycle. All vent system leaks must be sealed prior to the installation of the Power Venter. Flue gas temperature must not exceed 600oF at Power Venter Inlet. HS-2 SERIES POWER VENTER MOTOR INSTALLATION A. [. . . ] FOR "OLD STYLE" HS-2 MODEL (DATE CODE PRIOR TO 12/88, SEE DIAGRAM B. ) 1. Remove motor from motor mount by removing 4 nuts which secure it. NOTE: USE CARE SO AS NOT TO LOSE SPACERS AND NUTS. Position new motor so that studs extend into motor mount. Motor wires must match up with hole of junction box containing electrical shorty bushing. Feed motor wires through bushing and into junction box. Shaft must be inserted through wheel hub. Firmly fasten motor to motor mount (4 nuts) with a wrench. NOTE: BE SURE TO INCLUDE SPACERS BETWEEN MOTOR AND MOTOR MOUNT, AS WELL AS APPROPRIATE FASTENERS. Tighten wheel set screw on flat part of shaft. Wire Power Venter motor according to appropriate model on the opposite side of this sheet. Be sure grounding wire from motor is utilized. All wiring must be done in accordance with the NEC and applicable local codes. The wiring to the furnace should be protected by overcurrent protection (fuses or circuit brakers) rated 15 amperes or less, as applicable of 14 AWG conductors. CAUTION MUST BE EXERCISED TO ENSURE THAT WIRING DOES NOT COME INTO CONTACT WITH ANY HEAT SOURCE. Before testing installation, on "old style" units check sail switch in Power Venter junction box. Sail must operate freely in slot of fan housing. Operation of switch can be determined by hearing a "click" as switch opens and closes. [. . . ] 7.
TYPICAL HS-SERIES POWER VENTER GAS WIRING DIAGRAMS HSUL CONNECTED TO 24V ELECTRONIC IGNITION HSUL CONNECTED TO 24V STANDING PILOT
HST CONNECTED TO 24V ELECTRONIC IGNITION
HST CONNECTED TO 24V STANDING PILOT
TYPICAL HST-SERIES OIL WIRING DIAGRAM HST CONNECTED TO AN R8184G BURNER MOTOR LESS THAN 3 AMPS @ 120 VAC SERVICE Specific instructions cannot be made concerning frequency of lubrication. Usually oiling every 3 months during the heating season will be sufficient. NO MORE THAN 3 DROPS of SAE 20 oil should be used. Oil holes or lances are provided at the front and rear faces of motor. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-1021 MOTOR KIT 8504049 REV 2 1196 will begin.
