User manual TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196. We hope that this TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196 user guide will be useful to you.
Lastmanuals help download the user guide TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196.
Manual abstract: user guide TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196
Detailed instructions for use are in the User's Guide.
[. . . ] When wiring is completed, check all components by running system through its entire heating cycle. All vent system leaks must be sealed prior to the installation of the Power Venter. Flue gas temperature must not exceed 600oF at Power Venter Inlet. [. . . ] Install (4) nuts removed from step 2 and fasten tightly. Install metal conduit wire whip into the electrical box and secure with conduit nut. Install Black, White and Green wires back to their original connections. Re-establish power and run through a heating cycle making sure HS-3 is operating properly. FOR "OLD STYLE" (WITHOUT CONDUIT WIRE WHIP ATTACHED TO MOTOR). NOTE: NEW MOTOR WITH CONDUIT MAY REQUIRE ADDITION OF NEW JUNCTION BOX (INSTALLER SUPPLIED) ON OLDER HS-3 MODELS. Disconnect Black, White and Green motor wires from inside the junction box. Remove motor assembly from housing by loosening (4) nuts which fasten motor mount assembly to housing. Loosen Power Venter wheel set screw with a 5/32" allen wrench and remove wheel from motor shaft. Loosen nuts which fasten junction box to motor. Place wheel on new motor with not more than 1/4" gap between wheel back plate and motor mount plate. Install new motor/wheel assembly into housing making sure oil holes are facing up. Install (4) nuts removed from step 2 and fasten tightly. Mount new electrical box on sidewall (within 2 feet of venter). Run the conduit wire whip to the new electrical box, replace Black, White and Green wires to their original connections. NOTE: THIS MAY REQUIRE INSTALLATION OF RELAYS FROM OLD ELECTRICAL BOX INTO NEW ELECTRICAL BOX. [. . . ] Draft control on Power Venter should be adjusted so that there is no spillage at draft diverter, barometric or hood.
NEW STYLE HS-3 WITH FACTORY WIRED JUNCTION BOX GAS WIRING TO ANY APPLIANCE EQUIPPED WITH 24V CONTROLS
OLD STYLE HS-3 GAS WIRING TO ANY APPLIANCE EQUIPPED WITH 24V CONTROLS
SERVICE Specific instructions cannot be made concerning frequency of lubrication. Usually oiling every 3 months during the heating season will be sufficient. NO MORE THAN 3 DROPS of SAE 20 oil should be used. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-1022 MOTOR KIT 8504050 REV. 1 1196 will begin.
