User manual TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH. We hope that this TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH user guide will be useful to you.

Lastmanuals help download the user guide TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH.

Mode d'emploi TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH

Download

Manual abstract: user guide TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH

Detailed instructions for use are in the User's Guide.

 [. . . ] Discontinued Old-Style Switch

TJERNLUND PRODUCTS,  INC. 
1601 Ninth Street · White Bear Lake,  MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com

IMPORTANT: This gas pressure switch is an updated version with only one 1/4" aluminum tubing connection to the pressure tap port of gas valve. The atmospheric vent connection is no longer required,  as on the Old-Style Switch.  [. . . ] The screws do not require the use of a drill and their 1/2" length assures that the inner tank will not be penetrated. Mount the gas pressure switch by securing it to the heater casing with a screw in each of the two mounting holes. IMPORTANT: Mount gas pressure switch so that diaphragm is in a VERTICAL position,  (See New Switch Diagram). Install the supplied 1/8"-NPT pipe plug to the 90o port of the supplied 1/8-NPT black pipe tee,  (See New Switch Diagram). Use thread sealant,  do not over tighten. Install the 1/8-NPT black pipe tee to the gas pressure switch,  (See New Switch Diagram). Use thread sealant,  do not over tighten. CAUTION: Utilize the hex nut on the gas pressure switch when attaching the black pipe tee. Install the supplied Brass 1/8-NPT male x ¼" compression fitting to the 1/8-NPT black pipe tee,  (See New Switch Diagram ). Use thread sealant,  do not over tighten. Remove the PRESSURE TAP plug from the underside of the thermostat/gas control valve and install the supplied Brass 1/8-NPT male x ¼" compression fitting,  (See New Switch Diagram). Use thread sealant,  do not over tighten.  [. . . ] New-Style Gas Pressure GAS PRESSURE SWITCH THERMOSTAT/ Switch Installation
GAS CONTROL VALVE
MOUNTING HOLES GAS SUPPLY

BRASS 1/8-NPT MALE x 1/4" COMPRESSION FITTING
COMMON NORMALLY OPEN

1/8-NPT BLACK PIPE TEE 1/8-NPT PIPE PLUG - NEW PRESSURE TAP PORT IMPORTANT: GAS PRESSURE SWITCH DIAPHRAGM MUST BE MOUNTED VERTICALLY. 
1/4" OUTSIDE DIAMETER ALUMINUM TUBING - CONNECT TO PRESSURE TAP FITTING OF THERMOSTAT / GAS CONTROL VALVE. THERMOCOUPLE BURNER GAS LINE IMPORTANT: DO NOT ALTER PILOT GAS LINE INSTALL BRASS 1/8-NPT MALE x 1/4" COMPRESSION FITTING INTO PRESSURE TAP PORT. 
FIGURE 700S107 2/13/04

©2004 TJERNLUND PRODUCTS,  INC.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-2080 NEW STYLE GAS PRESSURE SWITCH will begin.