User manual TOPCOM BR 604

[. . . ] Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, TOPCOM reserves the right to make changes to the products described in this document without notice. TOPCOM does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The Port Settings button is on either the Details or Port tab, depending on your version of Windows. An example screen is shown below: Items shown on this screen are as follows: · Port If desired, click Browse to select a different device. The `Select Device Port' button supports multi-port models, but the firewall is a single-port print server. The Port Name is shown in the Printer's Properties. · Banner Check this option to print a banner page before each print job. The User Name will be printed on the banner page. If using a PostScript Printer, check the PostScript box. · Retry Interval Determines how often Windows will poll the print server to establish a connection when the printer is busy. LPD/LPR Printing from Windows LPD/LPR printing is supported by Windows NT 4. 0 Server and Windows 2000/XP. No software needs to be installed on the client PCs. Third-party drivers are available for earlier versions of Windows. 7-4 Print Server Reference Manual for the Model FR114P, FR114W and BR 604 Cable/DSL ProSafe Firewall Windows NT 4. 0 Server Configuration To use LPD printing, Microsoft TCP/IP Printing must be installed and enabled. This can be checked using Start-Settings-Control Panel-Network - Services. You should advise client PCs of the Server name and this printer name. Complete the Add Printer wizard. 8. Client PC Setup for LPD/LPR Printing After configuring the Windows Server, client PCs on the LAN can install the new printer. The following procedure is for Windows 95/98/ME, Windows NT4. 0, and Windows 2000 workstation. 1. 2. From Start -> Settings, open the Printers folder, and start the Add Printer Wizard. When prompted, select Network Printer. Print Server 7-7 Reference Manual for the Model FR114P, FR114W and BR 604 Cable/DSL ProSafe Firewall 3. 7. When prompted for Network Path or Queue Name, click the Browse button, and locate the Server and Printer that your Network Administrator advised you to use. Select the correct printer Manufacturer and Model, then click Next. Follow the prompts to complete the Wizard. The new printer will be listed with any other installed printers, and may be selected when printing from any Windows application. 7-8 Print Server Reference Manual for the Model FR114P, FR114W and BR 604 Cable/DSL ProSafe Firewall Network Printing from the Macintosh Macintosh computers can connect to a TCP/IP network printer using the Line Printer Remote (LPR) protocol. LPR printing can be set up on any Macintosh that has Desktop Printing installed or available. Desktop Printing is supported on MacOS versions beginning from 8. 1. [. . . ] Glossary IKE IP IP Address IPSec ISP LAN local area network MAC address Mbps MSB MRU Maximum Receive Unit Most Significant Bit or Most Significant Byte 2 Reference Manual for the Model FR114P, FR114W and BR 604 Cable/DSL ProSafe Firewall NAT netmask See Network Address Translation. A number that explains which part of an IP address comprises the network address and which part is the host address on that network. It can be expressed in dotted-decimal notation or as a number appended to the IP address. For example, a 28-bit mask starting from the MSB can be shown as 255. 255. 255. 192 or as /28 appended to the IP address. [. . . ]