User manual TORNADO T6626 INSTALLATION INSTRUCTIONS

[. . . ] 21 Ordering the correct dustbags and filters . 23 When to change the dust compartment filter (for motor protection) . 24 How to change the dust compartment filter . 26 Replacing one type of exhaust filter with another . [. . . ] ^ To release the handle from the suction tube, press the locking button (see arrow) and pull the handle away from the suction tube. Adjusting the electro telescopic suction tube One part of the electro-telescopic tube is packed inside the other and can be adjusted to suit your height for comfortable vacuum cleaning. ^ Press the telescopic tube release button (see arrow) to release the tubes and adjust to the required height. Then release the button to lock the tube in position. 10 Preparing for use Using the Electrobrush Important: please observe the flooring manufacturer's cleaning and care instructions. The Electrobrush is particularly suitable for intensive vacuuming of carpets which are subject to hard wear. It is very effective at removing deep seated dirt and preventing areas of frequent use being trodden into a path. , Please note that the Electrobrush should not be used for vacuuming deep-pile rugs and carpets or valuable hand-knotted rugs and carpets, e. g. There is a danger of the threads being pulled out. If in doubt, contact the carpet manufacturer/ retailer. , Do not use the SEB 217 Electrobrush to clean highly variable or uneven floors. The brush might come into contact with the floor and cause damage. Connecting the electro telescopic suction tube and the Electrobrush ^ Insert the electro telescopic suction tube into the Electrobrush until it clicks into position. For further information on use and maintenance please refer to the separate instructions supplied with the Electrobrush. 11 Preparing for use Using the standard floorhead Important: please observe the flooring manufacturer's cleaning and care instructions. The floorhead can be used for all normal cleaning of carpets and rugs. The Miele filter system consists of three filters which must be replaced from time to time to ensure that your vacuum cleaner performs efficiently. ­ Dustbag ­ Dust compartment filter (for motor protection) ­ Exhaust filter Purchasing new dustbags and filters Replacement dustbags and filters can be obtained from your local Miele Dealer or directly from the Miele Spare Parts Department (see back cover for contact details). Ordering the correct dustbags and filters When ordering dustbags for this cleaner, ask for bags with the code G/N. A dust compartment filter and a Super Air Clean exhaust filter are supplied with every packet of Miele dustbags. If you wish to purchase dust compartment filters or exhaust filters separately, please quote the model number of your appliance when ordering to ensure you get the correct items. Always quote the model number given on the data plate located underneath the appliance. You can replace the Active HEPA exhaust filter fitted in the vacuum cleaner with one of the other Miele exhaust filters if you wish (see "Optional accessories"). , To ensure that your vacuum cleaner functions correctly, cleans hygienically and gives you many years of trouble-free operation, please only use genuine Miele approved dustbags and filters. The use of non-Miele approved dusbags and accessories could invalidate your warranty and cause damage to your product. 21 Maintenance and care When to change the dustbag Change the dustbag when the colour marker in the dustbag change indicator fills the display, or sooner if it is no longer effective (see possible reasons for this below). Miele dustbags are disposable, and designed for single use only. Do not attempt to re-use them as suction would be reduced. Checking the dustbag change indicator ^ Attach the standard floorhead to the suction tube. Do not use any of the other floorheads or attachments as they will cause the dustbag change indicator to give a false reading. [. . . ] A temperature limiter switches the vacuum cleaner off automatically if it gets too hot. The overheating warning light will then come on to indicate that it has overheated. This can occur if, for instance, large articles block the suction tube or when the filter bag is full or contains particles of fine dust. A heavily soiled exhaust or dust compartment filter can also be the cause of overheating. [. . . ]