User manual TORNADO TO3400

[. . . ] ·Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. ·Do not use to pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. ·Do not use without dust bag and filters in place. ·Turn off all controls before unplugging. [. . . ] 1. Handle 2. ON/OFF switch 3. Quick release cord hook 4. Exhaust filter 5. Crevice tool 6. Handle release 7. Carrying handle 8. Hose 9. Extension wand 10. Combination tool 11. Power control (some models only) Front Back WARNING! OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE. Step 1. Attaching the Handle 1-2 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 1-3 Insert the screw provided into the existing hole. Tighten the screw securely with a screwdriver. Before securing the handle, please check that the handle is fitted to the vacuum body and make sure there's no gap. Step 2. Attaching the Hose and Tools 1-4 Slide the end of the hose wand with tabs into the suction intake valve. 1-5 Slide the extension wand and the crevice tool together into the storage clip. 2 DJ68-00075A 2001. 7. 52:24PM 4 Operation 2-1 2-2 2-3 ON-OFF Switch 1. To turn cleaner ON(I), press the ON/OFF switch to the ON position. 2. To the cleaner OFF(O), press the ON/OFF switch to the OFF position. Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle. Transporting cleaner To move your cleaner from room to room, put the handle in upright position, tilt the cleaner back on its rear wheels and push forward. 2-4 2-5 A B C Carrying handle The cleaner can also be moved by using the carrying handle. Cleaning Tool attachments Attachment tools can be used to clean furniture or drapes, on stairs or in corners. Place the vacuum on the floor with the handle in the upright position. while using attachment tools. Do not place the vacuum on top of furniture or steps as the brushroller may cause damage. Combination tool: Two types of cleaning tools are included in one attachment: rotate for desired tool. ·Use brush side to dust furniture, blinds, books, lamps, shelves. Grasp filter (B) and pull it straight out. Micro filter Reposition new filter by reversing this procedure. HEPA filter (some models only) This filter will become dirty and needs to be replaced about once a year to maintain efficient filtration. Reposition new filter by reversing this procedure. Do not operate cleaner without either the secondary or final filter in place. Check agitator shield Because your cleaner picks up so well, we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters. Removing debris under the shield will help maintain your cleaner's excellent pick up and suction. Disconnect cleaner from electrical outlet. Check for dirt accumulation by removing bottom plate (Fig. 3-11), and lifting agitator shield (Fig. Remove any debris and replace shield, agitator and bottom plate (Figs. 3-13 to 3-15). 4 DJ68-00075A 2001. 7. 52:24PM 6 Maintenance The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. [. . . ] Tighten screws securely. How to replace Disconnect cleaner from electrical outlet. Remove bottom plate, belt and agitator following directions in "The belt" section beginning with Fig. Continue following the directions in "The belt" section to reposition belt, new agitator and bottom plate. 5 DJ68-00075A 2001. 7. 52:24PM 7 Maintenance Clearing Clogs Disconnect cleaner from electrical outlet. The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the dust bag can sometimes become clogged. [. . . ]