User manual TOSHIBA 19AV616DG INSTALLATION

[. . . ] AV61*D* DIGITAL Series Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and important information . . . . . . . 4 The remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Inserting batteries and effective range of the remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Highlight Channel Sort and press or to select. Pressing to check two channels to swap the positions. Digital Channel Range Scan Scan channels from certain range. You can set the range before you scan the channels. Highlight Digital Channel Range Scan and press or to select. Using , , and to set the range, then press to scan. 1 2 3 4 5 6 7 8 9 10 Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital OK Channel Sort TF1 TMC NRJ12 LCI Eurosport France 24HTVE CLANTVE La2 TVE1 RNE1 Select RETURN Set Back EXIT Exit Channel Edit Edit the channel number and channel name. Digital Channel Range Scan Scan with a range of channels. 0% Select Channels from the SETUP menu. Highlight Channel Edit and press or to select. Using or to highlight the channel and press to select. Exit From Channel To Channel 21 69 OK Scan RETURN Back 4 EXIT Change the Channel Number by using the number buttons 0~9. Change the Channel Name by pressing the number buttons 0~9 to enter numbers and letters. NOTE: Colour System/Sound System can be changed only in Analogue TV. Channels Edit Network Name: R seau Num rique Terre Channel Number: 1 Channel Name: TF1 Frequency 490 Colour system Auto Sound system B/G OK Set Select RETURN Back EXIT Exit 20 TUNING THE TELEVISION English Channel Decode Channel Decode support the Canal+ (paid television channel); however, the channel also broadcast some un-encrypted programmes. These programmes without encryption can be viewed free of charge. Highlight Channel Decode and press or to select. Use or to highlight the channel and press to set. Reset Default Selecting Reset Default will reset all TV settings to their original factory values, excludes Country, Language OSD, and Channels. In the SETUP menu press to highlight Channels and press or to select. Select OK to confirm or select Cancel to exit. General controls Selecting programme positions To select a programme position use the numbered buttons on the remote control. Programme positions can also be selected using P P. programme position, input mode or stereo/mono signal, press . Press again to cancel. Analogue Channel Fine Tune When the reception is poor, you can use this function to do the fine tuning. In the SETUP menu press to highlight Channels and press or to select. Press to highlight Analogue Channel Fine Tune and press to select. to select the Stereo and Bilingual transmissions If stereo or dual language broadcasts are transmitted the word Stereo or Dual will appear on the screen each time programme positions are changed, disappearing after a few seconds. If the broadcast is not in stereo the word Mono will appear. Press to select Stereo or Mono. 4 Use or to adjust the frequency. [. . . ] The table below lists the software components pre-installed in the TOSHIBA Digital Televisions, which are subject to EULAs. The user should read the applicable EULAs carefully before using these software components. The EULAs are exhibited in their original text (English) as exactly written by the respective parties other than TOSHIBA. Pre-Installed Software FreeType ICU EULA Exhibit A Exhibit B 40 IMFORMATION English Exhibit A Portions of this software are copyright © <2007> The FreeType Project (www. freetype. org). All rights reserved Exhibit B ICU License - ICU 1. 8. 1 and later COPYRIGHT AND PERMISSION NOTICE Copyright © 1995-2006 International Business Machines Corporation and others All rights reserved. [. . . ]