User manual TOSHIBA B-SA4TM

[. . . ] TEC Thermal Printer B-SX4T SERIES Owner's Manual CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: · Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) · Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich sein. Centronics is a registered trademark of Centronics Data Computer Corp. Microsoft is a registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation. As an ENERGY STAR® Partner, TOSHIBA TEC has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. [. . . ] INTEL Simple Flash Memory TECNOLOGY Card (4 MB) Mitsubishi PC Card KING MAX Centennial Technologies Inc. PC Card Mitsubishi Maxell Flash Memory Card (1 MB) Mitsubishi E2-13 2. PRINTER SETUP ENGLISH VERSION EO1-33034 2. 10 Test Print 2. 10 Test Print A print test should be performed to check that the printer is operating correctly. The following paragraphs guide you through the diagnostic procedure for test label printing. Please follow the step-by-step procedures exactly for best results. For best results, use labels that are 76 mm or longer in length. Press and hold the [FEED] and [PAUSE] keys while turning on the printer power switch. The LCD Message Display will show the following message. !', $* $ 3. Press the [FEED] key three times to advance to the test print mode as indicated by the following message in the LCD Message Display. !7(67 35, 17 4. Press the [PAUSE] key and the print condition setting display will appear. !7(67 35, 17 35, 17 &21', 7, 21 5. Press the [PAUSE] key and the issue count setting display will appear. Set the issue count with the [FEED] or [RESTART] key. !7(67 35, 17 , 668( &2817 6. Press the [PAUSE] key and the print speed setting display will appear. Set the print speed with the [FEED] or [RESTART] key. !7(67 35, 17 35, 17 63((' ´V NOTES: 1. Select the sensor type which matches the media being used. Basically, the Reflective Sensor (Black Mark Sensor) is for tag paper, and the Transmissive Sensor (Feed Gap Sensor) is for labels. Select the print mode which matches the media being used. Basically, the thermal transfer is with ribbon, and the thermal direct is without ribbon. 7. Press the [PAUSE] key and the sensor type setting display will appear. Select the sensor type with the [FEED] or [RESTART] key. !7(67 35, 17 6(1625 75$16 8. Press the [PAUSE] key and the print mode setting display will appear. Select the print mode with the [FEED] or [RESTART] key. !7(67 35, 17 357 7<3( 75$16)5 E2-14 2. [. . . ] (However, [LF] and [NUL] will not be displayed. ) Example 1 [ESC] T20 G30 [LF] [NUL] Command error The following message appears. 7* %6;79$ Example 2 [ESC] XR; 0200, 0300, 0450, 1200, 1, [LF] [NUL] Command error The following message appears. ;5 %6;79$ Example 3 [ESC] PC001; 0A00, 0300, 2, 2, A, 00, B [LF] [NUL] Command error The following message appears. 3&$ %6;79$ · When the error command is shown, "?(3FH)" appears for codes other than codes 20H to 7FH and A0H to DFH. EA2- 2 APPENDIX 3 INTERFACE ENGLISH VERSION EO1-33034 APPENDIX 3 INTERFACE APPENDIX 3 INTERFACE Interface Cables To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: · Fully shielded and fitted with metal or metallised connector housings. · Should not be bundled tightly with power cords. · Should not be tied to power line conduits. RS-232C Cable description The serial data cable used to connect the printer to the host compute should be one of the following two types: DB-9S Connector to PC Pin No. [. . . ]