User manual TOSHIBA B-SP2D

[. . . ] TEC Portable Printer B-SP2D SERIES Owner's Manual CE Compliance (for EU only) This product complies with the requirements of EMC, Low Voltage and R&TTE Directives including their amendments. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] INSTALLING THE PRINTER EO1-33038 4. 1 LOADING THE BATTERY 2) Load a fully charged battery into the printer with the electrode facing down. NOTE: Load the battery in the correct orientation as indicated in the following picture. Battery Pack 3) Close the battery cover completely. NOTES: 1. If the battery cover is not completely closed, the battery pack may drop from the printer while it is carried, causing injury. Be careful not to apply excessive force to the battery cover when it is opened, as this may break the battery cover. Battery status indication at the power on time Fully charged: Flashes in red for a few seconds, and then lights in green. Battery near end: Flashes in red for a few seconds, and then lights in orange. Low battery: Flashes in red for a few seconds, and then lights in red. If the status indicator does not light at all, there may be one of the following problems: · The battery pack is not loaded. (The battery has been excessively discharged. ) · The printer is faulty. INSTALLING THE PRINTER EO1-33038 4. 2 INSTALLING THE MEDIA GUIDE 4. 2 INSTALLING THE MEDIA GUIDE WARNING!A cutter is attached to the inside of the media cover. Care should be taken not to injure your hand with the cutter when opening the cover. NOTE: The media guides are not required for a 58 mm wide media roll. 1) Slide the media cover release catches inside and open the media cover. Media Cover Media Cover Release Catch 2) Fit one media guide into the media holder's edge of the operation panel side, and the other one into a groove which corresponds to the width of media to be used. First insert side (1), then (2) until it snaps in position. NOTE:Be sure to fit the media guide in parallel with the grooves. Media Guide Operation Panel Side (2) (1) Media Holder 4- 3 4. INSTALLING THE PRINTER EO1-33038 4. 2 INSTALLING THE MEDIA GUIDE NOTE: When using a 55 mm wide media roll, attach the media guides to both edges of the media holder. When using a meida roll which is narrower than 55 mm, move only the media guide on the printer's bottom side (opposite side to the operation panel). The position of the media guide of the operation panel side is fixed. 3) To remove the media guide, first unhook side (1), and then (2). (1) (2) Media Guide Media Holder 4- 4 4. INSTALLING THE PRINTER EO1-33038 4. 3 INSTALLING THE MEDIA GUIDE FOR OUTSIDE WOUND PAPER 4. 3 INSTALLING THE MEDIA GUIDE FOR OUTSIDE WOUND PAPER Either roll direction is acceptable on this printer. Outside wound paper Inside wound paper However, when using the outside wound paper, it is necessary to fit the media guide for outside wound paper. Without this part, a paper jam may occur. When fitting the media guide for outside wound paper, insert it into the slits of the printer. NOTES: 1. When using outside wound paper that is 34 to 55mm wide, first fit the media guides, and then the media guide for outside wound paper. Do not fit the media guide for outside wound paper when using an inside wound paper. [. . . ] TROUBLESHOOTING Other problems Cause Corrective action Inquiries cannot be The printer power is not Turn on the power. (GH30 model only) Move the printer closer, The printer is positioned out of communi- within 3 m. The operating area is subject to noise or interference. Avoid such locations. One minute has passed Make an inquiry within since the printer power one minute after power on. [. . . ]