User manual TOSHIBA CN36G95

[. . . ] Electrical energy can perform many useful functions. This TV set has been engineered and manufactured to assure your personal safety. However, improper use can result in potential electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this TV set, observe the following basic rules for antenna/TV installation, use and servicing. [. . . ] · When you make a menu selection, your changes occur immediately. You do not have to press MENU or EXIT to save your changes. Note: The TV front panel does not have an EXIT button. · When you are finished programming the menus, you can press EXIT to clear the on-screen display, or wait 15 seconds and the on-screen display will disappear automatically. Your changes are automatically saved either way. TV Front Panel MENU TV / VIDEO VOLUME CHANNEL POWER MENU yzx · Changing the on-screen display language You can choose from three different languages (English, French, or Spanish) for the on-screen display of menus and messages. To select an on-screen display language: 1. Press x or · until the SET UP menu appears. Press x or · to highlight your desired language. LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 1 4 7 100 2 5 8 0 3 CH 6 9 CH RTN VOL ENT C. CA PT ADV/ PIP CH MENU NU ME Setting up your TV SET UP CONFIGURE LANGUAGE: [ENGLISH] FRANCAIS ESPANOL ANT1/2: TV/CABLE: CH PROGRAM ADD/ERASE: MORE MOVE [ ] [ANT1] ANT2 [TV] CABLE [ADD] ERASE SELECT [ ] LANGUE: ENGLISH [FRANCAIS] ESPANOL ANT1/2: [ANT1] ANT2 TV/CABLE: [TV] CABLE PROGRAMME CAN [ADD] EFF ADD/EFF: MORE BOUGER [ ] CHOISIR [ ] FAV ENTER FAV T SE RE EX IT ADV/ PIP CH EXIT Selecting the antenna input You can connect to one of two different antenna input sources (ANT 1 or ANT 2). Press x or · to highlight the SET UP menu. Press x or · to highlight either ANT 1 or ANT 2, depending on the antenna terminal you wish to use. SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL ANT1/2: TV/CABLE: CH PROGRAM ADD/ERASE: MORE MOVE [ ] [ANT1] ANT2 [TV] CABLE [ADD] ERASE SELECT [ ] 16 Selecting the signal source Use the TV/VIDEO button on the remote control or TV to monitor or change the signal source connected to your TV. Repeat steps 1­6 for other channels you want to add or erase, or press EXIT to return to normal TV viewing. FAV ENTER FAV RE SE T ADV/ PIP CH EX IT EXIT Changing channels To change to the next programmed channel: Press CHANNEL y z. To change to a specific channel (programmed or unprogrammed): Press the CHANNEL NUMBERS (0­9 and 100). Note: For channels 100 and higher, press the 100 button, and then the next two channel numbers (for example, to select channel 100, press 100, 0, 0; to select channel 125, press 100, 2, 5). 18 Using the TV's features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. To switch between two channels: 1. Select the first channel you want to view. Select a second channel using the CHANNEL NUMBERS (0­9 and 100). Every time you press CH RTN, the TV will switch back and forth between the last two channels you tuned the TV to. LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 1 4 7 100 2 5 8 0 3 CH CH CH (Channel) Channel Numbers 6 9 CH RTN VOL ENT CH RTN ME NU FAV T EX IT RE SE To program your favorite channels: 1. Tune the TV to a channel you want to program as a favorite channel. Press x or · to highlight the SET UP menu. Press y or z to highlight FAVORITE CH. SET UP MORE V-CHIP CONTROL FAVORITE CH CH LABEL VIDEO LABEL TIMER: DEMO: 0 MIN START [STOP] MOVE [ ] START [ ] SET UP FAVORITE CH [SET ] CLEAR 2 5 6 11 0 0 0 0 0 0 0 0 [TV: CYAN, CABLE: BLUE] 9. Repeat steps 1­8 for up to 12 channels, or press EXIT to close the menu. 19 Reference SELECT [ ] SET [ ] Index Appendix 5. Press x or · to display the FAVORITE CH menu. [. . . ] Limited Two (2) Year Warranty of Picture Tube TACP and THI further warrant the picture tube in this product against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. During this period, TACP and THI will repair or replace a defective picture tube at their option, with a new or refurbished picture tube, without charge to you, except that, if a defective picture tube is replaced after one (1) year from the date of the original retail purchase, you pay labor charges involved in the replacement. Rental Units The warranty for rental units begins with the first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first. Commercial Units Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture tube. [. . . ]