User manual TOSHIBA CZ27T31

[. . . ] Dusty places should also be avoided. Do not. . . DON'T remove any fixed cover as this may expose dangerous voltages. DON'T obstruct the ventilation of the equipment, for example, with curtains or soft furnishings. Overheating will cause damage and shorten the life of the equipment. DON'T allow electrical equipment to be exposed to rain or moisture. [. . . ] Press 2 So, to set your own, choose PICTURE from the top menu bar. PICTURE Contrast Brightness Colour Tint Sharpness Scan mode DNR 75 50 50 00 00 MM MM M M M M MM MM M M 1 u button will hold an image on the u again to return to TV mode. 100Hz AUTO Blue Screen. . . When no signal is being received, the TV will turn off the sound and switch the screen to blue. After 20 minutes the TV will switch to Standby mode. EXIT : To exit The Tint can only be adjusted on a sign al from an N TSC video recorder or DVD player wh en the television is in AUTO colour m ode. Within this PICTURE menu you have the options to adjust the Contrast, Brightness, Colour, Tint and Sharpness. 1 In the second section of the FEATURE MENU select Blue screen ON or OFF. Use the P buttons to and Q and down move up two-part this menu. ON M M 3 Using the S or R button alter to suit your taste. Blue screen EXIT : To exit 14 M FEATURE MENU SPECIAL SOUND FEATURES Dolby Digital Dolby Digital is available from DVD players, some games console players, etc. These must be connected using a Scart or phono lead for the picture AND an optical or a coaxial cable for the sound see page 23. Dolby Digital Arrange the speakers around your normal viewing positions (as shown on page 5) and then make sure that the TV is set up as follows: DELAY TIME. . . If you sit a long way from the TV and close to the rear speakers the sound from the rear will reach you before the sound from the front. You can use a higher setting in the Delay time option to restore the correct balance. 1 The DVD is connected to the TV using phono leads to the COMPONENT VIDEO INPUT or a Scart lead to Scart 3, and an optical or coaxial cable to the optical/coaxial sockets, DA-1 or DA-2. The Digital input in the AV CONNECTION menu (see page 22) is set to EXT3 if Scart 3 is used or EXT4 if the DVD is connected to COMPONENT VIDEO INPUT. If external front speakers are connected the external switch (found on the back of the TV) is set to EXT. Rear speakers are connected and the Rear Speaker option in the Surround set up menu is set to YES. 1 2 3 From the FEATURE MENU select Surround set up. With Delay time highlighted, use the S or R button to change the setting to a value that suits you. Press EXIT when you have finished. 2 3 4 If rear speake rs are NOT selected in th e Surround se t up menu, you will not hear any sound from your rear speakers. ! Adjustments 1 2 Set the volume and balance of the front speakers to your preference. Play a Dolby Digital source and press the button on the TV's remote control. Dolby Digital 3/2, is an indication of the channels available from your current sound source, see the table. Ideal for movies with stereo sound. Surround Sound: Disco To create the atmosphere of a room so full of music that it seems to engulf the listener. An ideal sound mode for listening to pop videos. Surround Sound: Off Uses only the front left and right speakers. This mode can be selected for watching news broadcasts and the like which require no special sound features. 17 TELETEXT Teletext ­ setting up This TV offers two ways of viewing text ­ AUTO and LIST which are explained on the next page. Selecting the character set and viewing mode and general information 2 With Character highlighted, use the R button to select your required character set: CHARACTER-1 or CHARACTER-2: TELETEXT CHARACTER-1 Auto MM M Back Character Mode MM CHARACTER-1 for: English Italiano Svenska Po polsku Srpski Italiano Français Español Português Romana Français Svenska Deutsch Jazyk Türkçe Jazyk Deutsch CHARACTER-2 for: P 3 4 P To select the Mode, with the the Q button highlight Mode. With the S and R buttons choose Auto or List. Press EXIT to finish. 5 About teletext VTR/DVD The TEXT TV button: Pressing the TEXT TV button once will bring up the teletext screen. Pressing it again will split the TV screen in two, with the TV picture and the text screen side by side. A third press will return you to the normal TV screen. You need to return to normal viewing if you wish to change channels. When you first press the TEXT TV button to access the text service, the first page you see will be the initial page. In Auto mode this displays the main subjects available and their relevant page numbers. VTR/DVD Selecting characters and modes Before using teletext you can choose the correct alphabet (Character) and whether to view in List or Auto mode (explained on the next page). In List mode you will see your chosen INITIAL page (explained on the next page). To access any teletext page, enter the 3 digit page number, using the numbered buttons on the remote control, e. g. [. . . ] If there are any speakers nearby, reposition them away from the TV before turning the TV off. Q Why is the video recorder picture in black and white?The input socket maybe set to S-Video in the AV CONNECTION menu. A Q 26 I have a picture, but why have I no sound?Press the volume button +j mute button. Why is the video picture good but there is no sound?See AV connections. A ­ or the sound k A M M MM M M function may not work. [. . . ]