User manual TOSHIBA D-R3

[. . . ] 00566A-D-R3_Cover 8/31/04 10:27 AM Page 1 DVD RECORDER D-R3 OWNER'S MANUAL Read this booklet first. 00566A-D-R3_Cover 8/31/04 10:27 AM Page 2 UK AK68-00566A 00566A-D-R3_2~13 8/31/04 10:27 AM Page 2 Getting Started Warning IMPORTANT NOTE TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used. [. . . ] - Do not select PDC or VPS unless you are sure the programme you wish to record is broadcast with PDC or VPS. Recording MOVE OK RETURN EXIT the . . . buttons then press the OK "Standard Timer" and or the . . . buttons to 4 Press the OKRecordbutton. selectthen "Scheduled List", and press or DVD-RAM(VR) Scheduled Record List Remaining Recording Time 02:12 SP No. Source 01 -- -Date --- -Start End Type -Mode V/P Edit -- Mode (Recording Mode) - FR : Select when you want to set video quality automatically. It depends on the remaining time on the DVD. - XP (high quality) : Select when video quality is important. 1 hour) - SP (standard quality) : Select to record in standard quality. 2 hours) - LP (low quality) : Select when a long recording time is required. (Approx. 4 hours) - EP (extended mode) : Select when a longer recording time is required. (Approx. 6 hours about 1. 2 Mbps) --:-- --:-- MOVE OK RETURN EXIT DVD-RAM(VR) Scheduled Record List Remaining Recording Time 02:12 SP No. Source Date Start End Type Mode V/P Edit No. 01 01 PR 01 01/ 01 12:00 14:00 Once SP Off Source PR 01 Date 01 JAN 02 -- -- --- -- --:-- --:-- --- -- Start Type V/P 12 : 00 Once Off End 14 : 00 Mode SP MOVE OK RETURN EXIT English -41 00566A-D-R3_36~46 8/31/04 10:29 AM Page 42 6 Press the OK button. q will appear on the front panel. It means that a timer recording is registered. Editing a Standard Timer If you make a mistake Press the oe button to select the item you want to change. If the timer settings overlap The programs are recorded in order of priority. If timer recording is set for the first program and then again for the second program and both programs overlap, the following message will appear on the screen: "This setting is identical with 1"The message shows that the first program has priority. After recording of the first program is complete, the second program starts being recorded. To exit without saving the current setting Press the MENU button. To return to the previous menu Press the RETURN button if you don't want to set a timer recording. Follow these directions to edit the timer record list. 1 Press the MENU button. buttons select 2 Press the . . . and thentopress the OK or "Programme" button. DVD-RAM(VR) Programme 7 Recording Turn the power off to finish the Timer Recording setting. Timer Recording will not work when the power is on. q Video Plus+ Record Standard Timer Video Plus+ Record Extended : Off will blink if disc is not inserted. MOVE OK RETURN EXIT s NOTE The timer recording time may differ from the set time depending on disc status and overall timer recording status (for example, recording times overlapping, or when the previous recording ends within 2 minutes before the start time of the next recording. ) You can make the Timer Recording up to 12 programmes. . . . and to select the "Standard Timer", then press OK or DVD-RAM(VR) Scheduled Record List Remaining Recording Time 02:12 SP No. Source 01 PR 01 02 -- -Date 01/ 01 --- -Start 12:00 End 14:00 Type Once -Mode V/P Edit SP -Off - s --:-- --:-- Flexible Recording (for Timer recording only) MOVE OK RETURN EXIT the . . . [. . . ] (See page 30. ) Cannot play the disc. Checkpoint 1 Check whether the disc is inserted correctly with the label facing up. Check the regional code of the DVD disc. This DVD recorder cannot play some types of discs. (See page 5, 47. ) The angle operation does not work while playing a DVD disc. Checkpoint 2 Checkpoint 3 Checkpoint 1 The angle operation is available only when the disc contains images captured from different angles. icon appears on the screen. [. . . ]