User manual TOSHIBA DRWST-53

[. . . ] Cleaning is particularly effective before humid rainy seasons. 0 Cleaning * When cleaning the machines, be sure to first unplug the power cord from the outlet for safety reasons. n Do not use benzine or alcohol, etc. , as these solvents will deteriorate the cover or cause the paint to peel. Leaving rubber orvinyl products in contact with the machines for long periods may leave stains on the machine surfaces. H Our maintenance service performs the periodical checks and other work required to maintain the quality and performance of the machines, preventing accidents beforehand. For details, please consult your sales agent or maintenance and service agent. n Cleaning the covers and keyboards: Wipe the covers and keyboards with a soft cloth. [. . . ] HOW TO FIX DRAWER IN PLACE ON THE TERMINAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 6. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copyright 0 1995 by TEC CORPORATION All Rights Reserved 2613 Nakameouro. JAPAN EOl-19022 DRWST-53 SERIES 1. INTRODUCTION Thank you for purchasing the TEC DRWST-53 Series Remote Drawer. This drawer can be connected to various terminals including the ST-4500 Series, which has been developed as a high-grade POS terminal. This drawer can be used as either first drawer or secondary drawer (the second drawer required). 1. I Precautions 1) Do not subject the equipment to sudden shocks. 4 3) 4) 5) 6) 7) 8) The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers. DO NOT POUR WATER directly onto the drawer and NEVER IMMERSE THE DRAWER IN WATER. Avoid using in locations subject to vibration and direct sunlight. Be sure to install the equipment on a flat surface. Be sure to use the equipment within the proper ranges of power, current consumption, temperature and relative humidity. Do not roughly open or close the drawer. Never attempt to modify the TEC equipment by yourself. 2. APPEARANCE AND NOMENCLATURE Drawer Cable Cash \ Drawer Release Lodt -l- DRWST-53 EOl-19022 SERIES Accessory 0 Parts `ITEC 9 Drawer Release Key (1 pc; 2 keys) sE"c P Cash Drawer Cover Key (1 pc; 2 keys) Flanged Screw (M4x8) (1 PC) Flanged Screw (M3X8) (1 PC) Nylon Clamp (1 PC) 3. INSTALLING THE DRAWER Turn the POWER SWITCH to OFF of the ST-4500 terminal before connecting the cables. Connect the connector of the Drawer Cable to DRWlT of the Control Unit. -2- DRWST-53 EOl-19022 SERIES 4. HANDLING OF THE DRAWER n Manual cash drawer releasing l Opening the Drawer Usually, the drawer is released automatically on finalizing each transaction. In the event of a power failure or othertroubles, the drawer can be opened in the following manner. [. . . ] Place the excessive cable in the area where the cable holder has been detached, excluding 25cm from the top of the drawer cable. Then, reattach the cable holder. \P , Cable Holder Drawer Cable -4- DRWST-53 EOl-19022 SERIES 3) Cut the grommet in the upper part of the drawer using a cutter. Take out the drawer cable from the upper part of the drawer and fix in place onto the drawer, using the nylon clamp and screw that are attached to the DRWST-53. Cable 4) Attach the drawer to the ST-4500 terminal and fix it in place with the screw attached to the DRWST-53. fr Flanged Screw (M4x8) DRWST-53 -5- DRWST-53 EOl -19022 SERIES 6. [. . . ]