User manual TOSHIBA FT6003BK

[. . . ] Do not use this product near water sources, such as bath tubs, wash bowls, kitchen sinks, laundry tubs, wet basements, or swimming pools. Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the telephone. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect the phone from overheating. [. . . ] Please take the time now to read your Owner's Manual carefully, so that you may enjoy the many convenient features of your SG-1700 telephone. FEATURES · 2. 4GHz Digital Spread Spectrum Transmission with Extended Talk Range · 30-Channel Auto Scanning · Digital Call Protect Privacy Scrambling and Digital Security Code · Volume Control (4 level) · Ringer Volume and Tone Control · 10 Speed Dial (20 digits) · Long Standby Battery Life (7 days) · One Way Page/Handset Locator · Last Number Redial (32 digits) · Mute on Handset · Any-key Answer · Reversible Charging System · Hearing Aid Compatible/HAC Volume · Desk/Wall Mountable (Bracket included) · Headset Jack 4 INSTALLATION 1. SETTING UP THE BASE UNIT For use on a desk or counter top follow the instructions below. DESKTOP MOUNTING: Snap the bracket's tab into the notches on the base. Raise the antenna to vertical position. Fasten the AC adaptor cord to prevent it from being disconnected. Telephone Line Cord Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120V, 60Hz) AC Adaptor · USE ONLY WITH Supplied AC ADAPTOR (TAC-1700; power source AC 120V, 60Hz/DC 9V). · The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use. ) 5 2. CHARGE THE BATTERY PACK Note Black Red Use only the supplied battery pack (TRB-8000; power source 600 mAh, 3. 6V). q Remove the battery compartment cover on the back of the handset by sliding it down. w Plug the battery pack cord into the connector in the battery compartment in correct polarity. e Place the battery pack in the battery compartment. r Put the battery compartment cover back by sliding until it snaps into place. Make sure not to get the wires of the battery pack caught in the cover. If the IN USE/CHARGE LED does not light, make sure the AC adaptor is plugged in securely and that the electrical outlet is working and not controlled by a light switch. It is important to charge the battery for IN USE/ CHARGE 12 to 16 hours continuously without LED any interruption before you use the handset for the first time. Charging contacts Note The battery pack is not charged properly if the charging contacts are dirty or tarnished. The last number called (up to 32 digits) will then be dialed again. 7. USING THE CALL WAITING SERVICE, ETC. To use this feature, you must subscribe to the Call Waiting service. RC008260) that has a 3/32-inch(2. 5mm) plug. To connect the headset, open the rubber cover on the left side of the handset, then insert the headset's plug into the jack. With a headset connected, you can make or answer calls as usual using the keys on the handset. You can use the supplied Belt Clip to hang the handset on your belt for greater convenience. When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack. Notes · The handset's earspeaker and microphone are turned off with a headset connected. · Pressing the / button of the handset also controls the connected headset's volume. · If you place the handset on the base unit while the headset is connected, be sure the handset is placed properly. 14 MEMORY DIALING You can store up to 10 telephone numbers in memory. Notes In memory dialing operation, · If more than 20 seconds elapse between pressing buttons, the operation will be cancelled and you must start over again. · If you press a wrong button, an error tone sounds and the handset returns to standby mode. · If a call comes in, the operation will be canceled and you will hear the ring. 1. [. . . ] Press CHANNEL to select a clearer channel, or relocate the base unit. · The volume control is set too high. · The base antenna is not in a vertical position. Lift the antenna to a vertical position. [. . . ]