User manual TOSHIBA IK-7100A

[. . . ] Refer all servicing to qualified service personnel. FIELD INSTALLATION MARKING: 71 Accessories Do not place this video product on an unstable cart, stand, tripod, bracket or table. The video product may fall, causing serious injury to a person, or serious damage to the product. Use only with stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessor y recommended by the manufacturer. IMPORTANT SAFEGUARDS ····································································1 COMPONENTS ······························································································ 4 PART NAMES AND FUNCTIONS ·································································· 4 CONNECTIONS ····························································································· 5 INSTALLATION ······························································································· 6 BACKLIGHT COMPENSATION ······································································ 7 DAY / NIGHT FUNCTION ··············································································· 7 NOTES ON USE AND INSTALLATION ·························································· 7 IN CASE OF PROBLEMS ·············································································· 8 SPECIFICATIONS ·························································································· 9 EXTERIOR VIEW ························································································· 10 161 Damage Requiring service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions. [. . . ] 39 inches (1, 000mm) 12V DC power supply GND Usage Limitation The product is not designed for any "critical applications1" "Critical applications" means life support systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass transit applications, military applications, homeland security applications, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage1 Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of the use of the product in any critical applications1 -3- Lower Mounting Bracket Hole Video Wire (BNC Tap) IR LED Camera Lens Illuminance Sensor Connect the video cable to a monitor or video device. The image is displayed when the camera is powered on. 39 inches (1, 000mm) -4- Do not overload power supply The recommended power supply for this camera is 7. 5 watts minimum at 12V DC. -5- 4. INSTALLATION Notes: · The attached screws and anchors are used to install the camera to a solid surface. concrete) If installing to loose or thin material surfaces , use the appropriate anchors (not included) with the screws. 4-1 Mounting the camera to a solid surface (1) Attach the Alignment Sticker to the surface. (2) Drill three pilot holes (Ø0. 28inch×1. 57inches(D)(Ø7mm×40mm(D))) through the three circles on the sticker. (3) Hammer the supplied plastic anchors into the holes. (4) Install the Mounting Bracket to the camera, secure using a wrench. IN CASE OF PROBLEMS Condition No image Unnatural color Flicker noise Check Points · Are the camera and connected equipment turned on?· Is the display monitor adjusted correctly?· Under the fluorescent lamp of 60Hz, flicker noise rarely occurs. 7. NOTES ON USE AND INSTALLATION · Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. · Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. · Treat the camera with care Do not drop the camera or subject it to intense vibration. -7- 4-2 Adjusting the view angle (1) The camera direction can be adjusted horizontally (pan: max. (2) To adjust pan and tilt rotate the Clamp Ring counterclockwise, and loosen the two Locking Screws using a screwdriver. -6- -8- 9. Image System Image Device Pixel Elements 2. Electrical TV System Horizontal Resolution S/N Ratio Minimum Illumination Gain Control White Balance White Balance Range Auto Electronic Shutter Backlight Compensation (BLC) Video Output Signal Synchronization System IR LED IR Distance 3. Mechanical Weight Dimension Ingress Protection Rating 4. Optical Built-in Lens View Angle of Lens 5. Power Input Voltage Current Consumption 1/3 inch CCD image sensor 768 (H) x 494 (V) NTSC 2:1 Interlace, 15. 734 KHz horizontal, 59. 94 Hz vertical 480 TV lines (typical) 48 dB 0 lux (LED is ON) Auto (AGC) Auto 2, 500 K to 9, 500 K 1/60 s to 1/100, 000 s Always On VBS (1. 0 Vp-p, 75 ohms unbalanced, BNC) Internal 16 High Light LEDs, 850nm 33 feet 1. 0 lbs (450 g) with mounting bracket 2. 8(W) x 2. 4(H) x 3. 4(D) inches (71mm(W) x 60mm(H) x 87mm(D) (excluding protrusion and mounting bracket)) IP66 f = 3. 6 mm, F 2. 0 71°(H), 53°(V) 12V DC ±10 % 0. 2A (MAX. ) 6. [. . . ] LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY. No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof, is herby limited to one (1) year from the date You discovered or should have discovered the problem. This limitation does not apply to implied warranties arising under state law. [. . . ]