User manual TOSHIBA IK-CU43A

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC rules. [. . . ] When the FUNC LOCK switch is set to ON, all settings except for the POWER switch 2 and the file item of the screen setting menu are locked out. 9 DOWN button p DC IN 12V terminal q EXT SYNC terminal w S-VIDEO terminal e VIDEO terminal r REMOTE terminal t FUNC LOCK switch 7 4. CONNECTION 4. 1 An Example of Standard Connection Monitor Camera control unit VIDEO Lens (Option) Camera head (Option) CAMERA DC IN 12V Camera cable (Option) DC 12V DC power supply 4. 2 Cautions on Connection · When connecting or disconnecting the camera cables (for the camera head and camera control unit), always turn off the power switch of the camera control unit first. · When connecting the camera, always turn off the power of the camera control unit and any other equipment connected. 1 Remove the camera head protection cover and mount a lens (option). 2 Connect the camera head and the camera control unit with the camera (option). input terminal of a monitor, etc. cable 3 Connect the VIDEO (or S-VIDEO) terminal of the camera control unit to a video 4 Connect a DC power supply (12V) to the DC IN 12V terminal of the camera control unit. · For DC power supply connecting to DC IN 12V terminal, use Class II DC power supply approved according to EN60950 in Europe. The AGC measurement area is the same as that used for "AREA". (Refer to item 7. 5) 6. 2 White Balance A white balance adjustment is necessary to obtain pictures with correct color tone. This camera allows you to select the white balance adjustment of "AUTO", "SET", and "MANU". With the AUTO mode selected, the camera adjusts the white balance automatically. Most shooting will be made in the AUTO mode. The following seven items can be set. 1 Scene file 2 Electronic shutter (AUTO/MANUAL), backlight correction 3 Pedestal level 4 Phase matching in external synchronization (horizontal/subcarrier synchronization) 5 White balance, auto electronic shutter, AGC measurement area 6 White balance offset 7 Scene file factory setting Main Menu Press the FUNC button to display the menu. Move the cursor to a desired item by moving the cursor up or down using the UP and DOWN buttons, and set an item by pressing the FUNC button. To quit the menu, move the cursor to END and press the FUNC button. FILE SHUTTER PEDESTAL SYNC AREA WB-OFFSET INIT. END PUSH FUNC TO SELECT A AUTO 00 INT LINK:1 00 UP button: FUNC The cursor position or data value goes up. DOWN button: The cursor position or data value goes down. FUNC button: Selects the item or data value. Notes: · When setting is changed in the menu screen, be sure to move the cursor to "END" and press the FUNC button to turn off the menu. · Don't turn off the POWER switch before turning off the menu. New setting is not stored, and old data remains. 13 7. 1 FILE (Scene File) There are two scene files A and B which can be selected according to the shooting state. FILE SHUTTER PEDESTAL SYNC AREA WB-OFFSET INIT. END PUSH FUNC TO SELECT A AUTO 00 INT LINK:1 00 1 Move the cursor to "FILE" in the main menu using the UP or DOWN button. 2 Press the FUNC button to display the contents to set FILE, A or B. Move the cursor to A or B using the UP or DOWN button. Press the FUNC button to set the contents. Note: · The scene file is for the menu screen. [. . . ] The protection cap protects the image sensing plane when the lens is removed from the camera, do not throw away. q When not using the camera for a longtime. If there is an intense light at a location on the screen such as a spot light, a blooming and smearing may occur. When intense light enters, vertical stripes may appear on the screen. Ghosts may occur when there is an intense light near the object. In this case, change the shooting angle. q Install the camera in a location free from noise. Stop supplying power. q When cleaning the camera Always turn off the power and clean with a piece of soft dry cloth. [. . . ]