User manual TOSHIBA KV-5124A

[. . . ] REFER SERVICING TO QUALIFIED PERSONNEL ONLY. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. USER-INSTALLER CAUTION : YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT CLOUD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THIS PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES. NOTE: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Use the SHIFT button and the SET button for settings and adjustments in the same manner. To return to the initial screen press the DISPLAY button. Monitor Screen (initial screen) MENU Screen (initial screen) MENU CLOCK SET SETUP DISPLAY MODE TIME DATE SEARCH CLOCK SET Screen CLOCK SET (DAYLIGHT SAVING TIME) PREPARATION i OUT (MONTH) (DAY) (YEAR) 1 / 1 / '95 SUN (TIME) 0:00 MENU=[DISPLAY] Comment Setting of clock. Unless the date-time is adjusted, the "PROGRAM" and "ALARM RECALL" will not appear on the MENU screen. 1/ 1/95 SUN 0:00:00 A 2 END=[DISPLAY] Monitor Screen (normal screen) MENU Screen (normal screen) MENU CLOCK ADJUST Screen CLOCK ADJUST (DAYLIGHT SAVING TIME) i Correction of date-time. RECORDING OPERATION CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH 8/28/96 WED 17:30:02 A 2 END=[DISPLAY] IN (MONTH) (DAY) (YEAR) 8 / 28 / '96 WED (TIME) 17:30 MENU=[DISPLAY] SETUP Screen MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] SETUP ALARM REC TIME SPEED 1SHOT REC FIELD INTERVAL RESTART REC TAPE END MODE ALARM 15S A 2H 1F 0. 2S OFF STOP STOP i i i i MENU=[DISPLAY] DISPLAY Screen MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] i i Setting of alarm recording mode (recording time, recording mode) Setting of One-Shot recording mode (number of recording fields, recording intervals). Setting of recording for restoration of power following a power failure. Setting of operation after detection of tape end (tape end detection mode for tape end detection during recording and when an alarm recording is made). Setting of display screen (date, day of week, time, recording time, VCR number, alarm). Setting of time display (24H, 12H). NOTICE PLAYBACK OPERATION 13 PROGRAM Screen MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] MO1 MO2 TU1 TU2 WE1 WE2 TH1 TH2 ON ON ON ON ON ON ON ON PROGRAM --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H --:-- § --:-- 120H MENU=[DISPLAY] i Setting of timer recording. ALARM RECALL Screen MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] AL1 AL2 AL3 AL4 AL5 AL6 AL7 1ST ALARM RECALL --/--/----- --:--:---/--/----- --:--:---/--/----- --:--:---/--/----- --:--:---/--/----- --:--:---/--/----- --:--:---/--/----- --:--:---/--/----- --:--:-MENU=[DISPLAY] i Alarm recall display TIME DATE SEARCH Screen MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] TIME DATE SEARCH DAY HOUR MINUTE SEARCH 1 0 00 FORWARD REVERSE MENU=[DISPLAY] 14 NOTICE PLAYBACK OPERATION RECORDING OPERATION i Set the day and time to be searched and searching direction. PREPARATION INTRODUCTION INTRODUCTION PREPARATION SETTING THE CLOCK An internal clock generates time and date for superimposing on the monitor screen. Adjust the time from the MENU screen (initial screen). After the clock is set, the data and time modes are displayed on the monitor screen (live picture). Operation In case of setting to 5:30 PM, Wednesday, August 28, 1996; 1 2 3 Press the DISPLAY button. MENU CLOCK SET SETUP DISPLAY MODE TIME DATE SEARCH 6 7 8 9 10 Press the SHIFT button to blink Year and press the + or ­ SET button to set to "96". DISPLAY ­ TIME MODE SET CLOCK SET (DAYLIGHT SAVING TIME) IN DISPLAY ­ TIME MODE SET SHIFT + TRACKING + TRACKING (MONTH) (DAY) (YEAR) 8 / 28 / '96 WED (TIME) 1:00 MENU=[DISPLAY] SHIFT LOCATION SELECT END=[DISPLAY] LOCATION SELECT Press the + SET button. CLOCK SET (DAYLIGHT SAVING TIME) OUT RECORDING OPERATION DISPLAY ­ TIME MODE SET SHIFT + TRACKING (MONTH) (DAY) (YEAR) 1 / 1 / '95 SUN (TIME) 0:00 MENU=[DISPLAY] Press the SHIFT button to blink Time in hours and press the + SET button to set to "17". DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT CLOCK SET (DAYLIGHT SAVING TIME) IN + (MONTH) (DAY) (YEAR) 8 / 28 / '96 WED (TIME) 17:00 MENU=[DISPLAY] LOCATION SELECT Press the + SET button and set the DAYLIGHT SAVING TIME to IN. CLOCK ADJUST (DAYLIGHT SAVING TIME) IN DISPLAY ­ TIME MODE SET SHIFT + TRACKING PLAYBACK OPERATION (MONTH) (DAY) (YEAR) 1 / 1 / '95 SUN (TIME) 1:00 MENU=[DISPLAY] Press the SHIFT button to blink Time in minutes and press the + SET button to set to "30". DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT CLOCK SET (DAYLIGHT SAVING TIME) IN + (MONTH) (DAY) (YEAR) 8 / 28 / '96 WED (TIME) 17 17:30 MENU=[DISPLAY] LOCATION SELECT 4 5 Press the SHIFT button to blink Month and press the + SET button to set to "8". DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT CLOCK SET (DAYLIGHT SAVING TIME) IN Press the DISPLAY button to start display of the set date and time. DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT MENU CLOCK ADJUST SETUP DISPLAY MODE PROGRAM ALARM RECALL TIME DATE SEARCH END=[DISPLAY] + (MONTH) (DAY) (YEAR) 8 / 1 / '95 TUE (TIME) 1:00 MENU=[DISPLAY] + NOTICE Press the SHIFT button to blink Day and press the + SET button to set to "28". DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT CLOCK SET (DAYLIGHT SAVING TIME) IN Press the DISPLAY button to return to the normal screen. ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT + (MONTH) (DAY) (YEAR) 8 / 28 / '95 MON (TIME) 1:00 MENU=[DISPLAY] DISPLAY + 8/28/96 WED 17:30:02 A 2 15 ON-SCREEN FUNCTIONS When the power is turned ON, the time and date modes are displayed on the monitor screen (live picture). On-screen displays are not available in the event of no video input signal. Date-Time Display VCR display 1 Date 2 Day of the week 8/28/96 WED 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 3 Time 4 Playback/Recording time Monitor screen 1 Date : Displayed with the month-day-year. 2 Day of the week : Automatically set to the correct day of the week when the date is set. i If the alarm recording is not carried out for more than those listed in the following chart then, the alarm may be skipped. i If the alarm recording interval is not left for more than those listed in the following chart then, the alarm may be skipped. i If there is not enough time between the beginning of the alarm search and the first alarm activation. If the time period is shorter than those listed in the following chart then, the first alarm may be skipped. Record mode A2 or A6 A12 A18 A24 Minimum alarm recording time needed 2s 15 s 7s 30 s Minimum alarm recording interval needed 7s 50 s 25 s 95 s Minimum recording time needed between start of search and first alarm activations 5s 15 s 65 s Tape Remain When the TAPE REMAIN button is depressed during recording or playback, the counter display changes to the remaining tape display. The remaining time is the approximately estimated time in the A2-hour mode to tape end. H REC SP TAPE REMAIN · The remaining time is the approximate remaining time. · Displays the remaining tape time estimated in the A2-hour mode. During computation of the remaining time, the following display appears. H REC SP · When the VCR has been used in the recording mode over a long period, it may take considerable time for computation. When operating at fast speed in the A2-hour mode, the computation is faster. Note: PLAYBACK OPERATION It is possible to compute the remaining time for T-120, T-90, T-60 and T-30 tape. The display will not be correct for other kinds of tape. Error Message When an abnormality occurs during operation, the error code is displayed. At the same time, the buzzer will sound continuously. H SP Code Number E-1 E-3 Condition of Abnormality Abnormality on reel rotation during tape running. [. . . ] When the VCR power plug is inserted to the AC outlet, recording starts and playback is not possible. i Adjust with the TRACKING button. i The video head may be clogged or worn out. Consult with your dealer. i Press the TRACKING button in a still playback mode and adjust. i Are you using an external synchronous or gen-lock synchronous video camera?i Is restart recording set to ON? PREPARATION Other matters No screen display appears. [. . . ]