User manual TOSHIBA MA-1595-1

[. . . ] TEC Electronic Cash Register MA-1595-1 SERIES Owner's Manual Supplement "This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. " "Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. " FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] Key operation on the ECR is unavailable during the inquiry to the host. Values 0 to 9 and A to Z should be used to enter the Authorization Code. Issuance of the Store Receipt is selectable. In the Receipt-OFF mode, payment by the EFT media cannot be made. (3) Cash-only Debit (Debit Refund) This operation is performed for canceling debit cashing transactions. 7 digits [DEBIT] Card Slide Input the Pin No. Store Receipt Print EFT terminal responds "APPROVAL". Customer Receipt Print NOTES: 1. Before performing this operation, the [DEBIT] key should be programmed with the status "nopurchase cashing is allowed". Also each EFT Media Key should be programmed with the statuses both "with EFT process" and "off line authorization is available". For the EFT function, do not perform any registration in Receipt OFF mode. Receipt post-Issue operation after the Cash-only Debit is unavailable. Key operation on the ECR is unavailable during the inquiry to the host. Training Cashiers are unacceptable to the EFT terminal. Issuance of the Store Receipt is selectable. 4- 3 4. OPERATIONS IN " - " MODE EO1-11152 4. 5 Prohibitive Operations In " - " Mode 8. When manual issuance of store receipt has been programmed, the store receipt must be issued to perform next transaction or read/reset jobs. 4. 5 Prohibitive Operations In " - " Mode · NO-SALE ([NS]) · AUTO-SCALE (described in 4. 3. ) · NO-SALE CASHING OF CHEQUE OR OTHER NON-CASH MEDIAS · NO-SALE EXCHANGE from Foreign Currency to Domestic Currency, or vice versa · LOAN · PICK UP · TRAINING MODE START/END · ENDORSEMENT PRINT · RECEIPT POST-ISSUE ([RECEIPT ISSUE]) 4. 6 Manager Intervention Required Status or Amount Limit In " - " Mode Since operations in the " - " mode are performed under the manager's control, the status requiring a Manager Intervention, and Amount Limits (described in Chapter 2) will all be released, i. e. , the same handling as in the "MGR" mode. 4- 4 5. READ (X) AND RESET (Z) REPORTS EO1-11152 5. READ (X) AND RESET (Z) REPORTS The following table shows the key operation to take each report. The "X" and "Z" reports have exactly the same print content if both are available, except that: 1. The "X" reports allow to read the sales data but not clear memories, while the "Z" reports allow to read the sales data and at the same time all the resettable memories will be cleared when the reports have been issued. The symbol "X. . . " is printed on the top line of a Daily Read Report, "Z. . . " on a Daily Reset Report, "GTX. . . " on a GT Read Report, and "GTZ. . . " on a GT Reset Report, as initial settings. A reset count is printed on the bottom of a "Z" report only. WARNING!When opening the cash drawer, be careful not to let the drawer hit any person. TABLE OF OPERATIONS FOR X AND Z REPORTS Daily Reports Mode Lock X Z X Z X Z Sample Page 5-5 Report Name FINANCIAL READ AND RESET · Financial Read · Financial Reset CASHIER READ AND RESET · All Cashier Read · All Cashier Reset · Individual Cashier Read · Individual Cashier Reset Key Operation 3 [AT/TL] (Drawer opens. ) 5-7 4 [AT/TL] (Drawer opens. ) Code Entry Method: 4 [#] |Cashier ID Code| [AT/TL] (2-digit manager-assign code) Cashier Key Method: Set the required Cashier Key (or depress the required Cashier Key), then 4 [#] [AT/TL] SALESPERSON READ AND RESET · All Salesperson Read · All Salesperson Reset CREDIT CARD COMPANY SALES READ AND RESET · Credit Card Company Sales Read · Credit Card Company Sales Reset DEPARTMENT GROUP READ MEDIA SALES AND IN-DRWER TOTAL READ HOURLY RANGE READ AND RESET · Hourly Read · Hourly Reset 5-8 X Z 5 [AT/TL] 5-8 X Z X X X Z 6 [AT/TL] 8 [AT/TL] 9 [AT/TL] (Drawer opens. ) 10 [AT/TL] 5-9 5-10 5-10 5- 1 5. [. . . ] As only one terminal is responding with some kind of status, a time out limit of 30 seconds is given (the "No response" status is not subject to the service timer). However, if S2 turns into a "Power ON" condition, it will also be subject to the service timer. 13- 1 13. OTHER OPERATIONS RELATING TO IN-LINE SERVICE EO1-11152 13. 2 Suspending 13. 2 Suspending This is to be operated for the purpose of suspending an in-line service being executed, when any terminals remain unserviced, and of going on to a "RETRY", "INCOMPLETE ENDING", or "CANCEL" operation as the next step. OPERATION ON MASTER TERMINAL: (Same Lock positions as the in-line job being performed) Depress [ITEM CORR] until the key-in tone is generated. [. . . ]