User manual TOSHIBA MW27FPX

[. . . ] Introduction DIGITAL VIDEO 2 COMBINATION FLAT COLOR TELEVISION AND VIDEO CASSETTE RECORDER / DVD VIDEO PLAYER Connections 13 Basic setup 18 TV operation MW24FPX MW27FPX OWNER'S MANUAL 23 Playback (VCR) 33 Recording (VCR) 38 Other functions (VCR) 42 Basic playback (DVD) 44 Advanced playback (DVD) 47 Function setup (DVD) 57 Others 61 Illustration of MW24FPX 2004 Toshiba Corporation This device does not tape-record copy protected DVD video discs. 5Q10501A [E]Cover 1 4/17/04, 11:55 AM Introduction IMPORTANT SAFEGUARDS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To return to playback, press PLAY or SLOW. During picture search mode there will be noise bars which are caused by the system. The Special Playback will automatically change to playback after approx. 5 minutes to protect the video tape against excessive wear. Slow tracking and vertical lock adjustment If noise bars appear in the picture during slow motion, press the TRK + / to reduce the noise bars. Frame by frame picture Press PAUSE/STILL during playback. Press SLOW one by one: The picture advances frame by frame. To return to playback, press PLAY or PAUSE/STILL. CM skip Press CM SKIP during playback. The unit will search forward through approximately 30 seconds of the tape (e. g. unwanted commercial time) for each press of CM SKIP (maximum six presses) and then resume normal playback. For example : 1 press: 30 seconds of tape 2 press: 60 seconds of tape 3 press: 90 seconds of tape 35 5Q10501A [E]p33-37 35 4/17/04, 11:58 AM Playback (VCR) Convenient function MENU DISPLAY REC PLAY COUNTER RESET // / Repeat playback Using the real time tape counter The entire video tape will be played until its end. The tape The on-screen real time tape counter shows the tape will automatically rewind to the beginning and the playback running time in hours, minutes and seconds. You can easily determine how long the tape has been running or will be repeated. how much time is left on the tape. 1 2 3 Press MENU, then press option. or to select 1 OFF Press DISPLAY. TV/VCR 8:40AM THU CH 012 ENTER TIMER REC SET AUTO REPEAT DISPLAY 00:30:50 SP / / / / MENU Press or to select "AUTO REPEAT". 2 OFF Press COUNTER RESET to set the counter to "00:00:00". TV/VCR 8:40AM THU CH 012 ENTER TIMER REC SET AUTO REPEAT / / / / MENU 00:00:00 SP Press or to select "ON" or "OFF". If "ON" is selected, the playback will be repeated endlessly. 3 4 Begin Playback or Recording to start the tape, the counter will display the elapsed time. PLAY REC ENTER TIMER REC SET AUTO REPEAT ON When you wish to make the counter disappear, press DISPLAY once again. / / / / MENU DISPLAY 4 5 Press MENU repeatedly until the menu screen is cleared. If you press DISPLAY, " " will appear on the screen 22 . To start the playback, press PLAY. PLAY The playback will be repeated endlessly. To cancel repeat mode: In step 3 above, press or to select "OFF" position. Press MENU repeatedly until the menu screen is cleared. The repeat function is canceled automatically when the unit is switched off. 36 5Q10501A [E]p33-37 36 4/17/04, 3:32 PM DISPLAY REC COUNTER RESET PLAY STOP ZERO RETURN Zero return function Video head cleaning The zero return function provides a convenient method of rapVideo head clogging idly returning to the starting point of recording or playback. The The video heads are the means by starting point can be indexed for any location on the tape by which the unit reads the picture from the tape during playback. In the unlikely pressing COUNTER RESET and ZERO RETURN. 1 2 Press DISPLAY. TV/VCR 8:40AM THU CH 012 DISPLAY 00:30:50 SP event that the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the unit checked by qualified service personnel. Good Picture Playback (VCR) Snowy Picture Video head cleaning Video head cleaning is needed when the playback picture becomes unclear. This signifies that the heads are getting dirty and can occur when playing poor quality or damaged tapes. If the heads require cleaning, use a equivalent high quality chemical non-abrasive (wet) head cleaning tape or have them cleaned professionally. If playing a head cleaning tape in the unit once does not improve the picture, play it several times before requesting service. Notes: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE REAR COVER. Video heads may eventually wear out and should be replaced when they fail to produce clear pictures. [. . . ] You must also deliver the entire product to a TACP Authorized Service Station. You are responsible for all transportation for the set to and from the Service Station. Limited Two (2) Year Warranty of Picture Tube TACP further warrants the picture tube in this product against defects in materials or workmanship for a period of two (2) years after the date of original retail purchase. During this period, TACP will replace a defective picture tube without charge to you except that if a defective picture tube is replaced after ninety (90) days from the date of the original retail purchase, you pay labor charges involved in the replacement. You are responsible for all charges involved in the replacement. [. . . ]