User manual TOSHIBA PDR-M25

[. . . ] Attention For customers in the U. S. A. DIGITAL STILL CAMERA PDR-M25 Getting Ready Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Basic Photography FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Playing Back/ Erasing Images NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press the ENTER button to set the manual setup screen to non-display. Page 54 Pressing the button displays the available Self-timer and Macro modes in order. [ ] Self-timer [ ] Macro [ ] Self-timer & Macro Off Playing Back/ Erasing Images Look at the image on the LCD monitor to compose the picture. Using the LCD Monitor Page 33 Other Applications Press the shutter button down half way, and press it down fully. Page 37 To cancel macro photography, press the Memo · Macro photography is not canceled even if the camera is turned off or the Auto Power OFF function is activated. · Only the [ ] Suppressed Flash and [ ] Forced Flash modes can be set for flash photography. · The settings are canceled when you remove or insert the batteries or disconnect or connect the AC adapter. button until off. Additional Information - 47 - Photography Using the Self-timer (Self-timer Photography) Getting Ready When the self-timer is used, the shutter automatically closes after the preset time (two or ten seconds). Changing the set time until photography Page 59 Set the mode dial to [ Press the ] or [ ]. Basic Photography button to set to the self-timer mode. Playing Back/ Erasing Images [ ] is displayed on the LCD monitor and the status display. In the Manual Photography mode, [ ] is not displayed on the LCD monitor when the manual setup screen is displayed. Press the ENTER button to set the manual setup screen to non-display. Page 54 Pressing the button displays the available Self-timer and Macro modes in order. [ ] Self-timer [ ] Macro [ ] Self-timer & Macro Off Compose the picture. Other Applications Press the shutter button down half way, and press it down fully. Page 37 The self-timer lamp flashes after lighting in red. The photograph is then taken after the preset time (two or ten seconds). When photographs are taken using the LCD monitor, the count down is displayed. To cancel photography midway, press the button. After you have set the self-timer, the setting is not canceled even if the camera is turned off or the Auto Power OFF function is activated. The setting is canceled when you execute the self-timer photography, remove or insert the batteries or disconnect or connect the AC adapter. Additional Information - 48 - Photography Using the Flash (Flash Photography) In the default setting, the flash will be automatically set to function in dark places. No special setting is needed to set off the flash. The flash firing mode can be set to suit the conditions where the flash is to be fired. The effective firing distance of the flash is approximately 1. 3 ft (0. 4 m) to 8. 2 ft (2. 5 m). Getting Ready Set the mode dial to [ ] or [ ]. Basic Photography Press the flash button to set to the desired mode while viewing the image on the LCD monitor or the status display. The icon for the mode that you selected is displayed in the LCD monitor or the status display. In the Manual Photography mode, the icon for the mode that you selected is not displayed on the LCD monitor when the manual setup screen is displayed. [. . . ] DCF (Design rule for Camera File System) A file system standard defined by the JEIDA (Japan Electronic Industry Development Association) that is required for exchanging data between digital still cameras or a digital camera and a printer. This standard defines the hierarchy and file names used when storing image files on memory cards or other recording medium. Exif File Format (Exchangeable Image File Format) A color still image format for digital still cameras approved by the JEIDA (Japan Electronic Industry Development Association). JPEG-compliant, this format is compatible with TIFF and JPEG and can be used in image processing software for most personal computers. [. . . ]