User manual TOSHIBA PORTEGE R200 (PPR20)

[. . . ] The programmable functions may be accessed via the easy-to-use menu or via the Direct Access Numbers listed in the PORTEGE R200 (PPR20) ASD Operation Manual. This feature, combined with Toshiba's high-performance software, delivers unparalleled motor control and reliability. The PORTEGE R200 (PPR20) is a very powerful tool, yet surprisingly simple to operate. The user-friendly Electronic Operator Interface (EOI) of the PORTEGE R200 (PPR20) has an easy-to-read 240 x 64 pixel graphical LCD screen. [. . . ] Over speeding a motor decreases its ability to deliver torque and may result in damage to the motor and/or the driven equipment. All PORTEGE R200 (PPR20) ASDs are equipped with internal DC bus fuses. However, not all PORTEGE R200 (PPR20) ASDs are equipped with internal primary power input fuses (HP dependent). When connecting two or more drives that have no internal fuse to the same power line as shown in Figure 3, it will be necessary to select a circuitbreaking configuration that will ensure that if a short circuit occurs in ASD 1, only MCCB2 trips, not MCCB1. If it is not feasible to use this configuration, insert a fuse between MCCB2 and ASD 1. Circuit breaker configuration. Mounting the ASD CAUTION Install the unit securely in a well ventilated area that is out of direct sunlight using the mounting holes on the rear of the ASD. The ambient temperature rating for the PORTEGE R200 (PPR20) ASD is from 14 to 104° F (-10 to 40° C). The process of converting AC to DC, and then back to AC produces heat. During normal ASD operation, up to 5% of the input energy to the ASD may be dissipated as heat. If installing the ASD in a cabinet, ensure that there is adequate ventilation. PORTEGE R200 (PPR20) ASD Quick Start Guide 13 Do Not operate the ASD with the enclosure door open. When installing multiple ASDs, ensure that there is a clearance space of at least 8 inches (20 cm) from the top and the bottom of adjacent units. Note: In the event that the motor rotates in the wrong direction when powered up, reverse any two of the three ASD output power leads connected to the motor. Figure 4. ASD/Motor connection diagram. Connect the 3-phase input power to the input terminals of the ASD at L1/R, L2/S, and L3/T. Connect the output of the ASD to the motor from terminals T1/U, T2/V, and T3/W. The input and output conductors and terminal lugs used shall be in accordance with the requirements listed in the section titled Cable/Terminal Specifications on pg. If conductors smaller than the recommended sizes are used in parallel for the input or output power, each branch of the parallel set shall have its own conduit and not share its conduit with other parallel sets (i. e. , place U1, V1, and W1 in one conduit and U2, V2, and W2 in another). Note: National and local codes should be referenced when running more than three conductors in the same conduit. Install a molded case circuit breaker (MCCB) or fuse between the 3-phase power source and the ASD in accordance with the 2005 NEC Article 430. CAUTION For 600 volt ASDs, the 15 HP or less ASDs (P/N VT130PORTEGE R200 (PPR20)U6015B ­ 6160B) require a class-J fuse rated at 600 Volts/30 A. A phase-shifting transformer (or other means) must be supplied by the user when configured for 12pulse operation. External fuses are required on the below-listed ASDs when configured for 12-pulse operation. VT130PORTEGE R200 (PPR20)U2600B(DR) VT130PORTEGE R200 (PPR20)U2750B(DR) VT130PORTEGE R200 (PPR20)U412KB(DR) VT130PORTEGE R200 (PPR20)U415KB(DR) VT130PORTEGE R200 (PPR20)U610KB(DR) VT130PORTEGE R200 (PPR20)U612KB(DR) VT130PORTEGE R200 (PPR20)U615KB(DR) Use either the Ferraz Shawmut Semiconductor fuse (P/N A70QS200) and fuse block P234C, or the Toshiba ASD-FUSEKIT-12P. The Toshiba kit includes the required fuses and the mounting hardware for the fuses. PORTEGE R200 (PPR20) ASD Quick Start Guide 15 Lead Length Specifications Adhere to the NEC and any local codes during the installation of ASD/Motor systems. Excessive lead lengths may adversely effect the performance of the motor. [. . . ] Complete the conduit and wiring connections. Install the Conduit Extender Box cover (P/N 53355 of Figure 25). Conduit Box/Cover. 50 PORTEGE R200 (PPR20) ASD Quick Start Guide Cable/Terminal Specifications Installation should conform to the 2005 National Electrical Code Article 110 (NEC) (Requirements for Electrical Installations), all regulations of the Occupational Safety and Health Administration, and any other applicable national, regional, or industry codes and standards. Note: The following ratings are guidelines and shall not be the sole determining factor of the lug or wire size used with the ASD. [. . . ]