User manual TOSHIBA PX1215E-1NAC

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC Rules. This Class A digital apparatus complies with Canadian ICES-003. [. . . ] Refer to the item "5. 1 White Balance", make the adjustment. Please see "5. 2 Gain", "5. 3 Switching video signal output" and "7. MODE SETTING BY THE ON SCREEN DISPLAY" to carry out necessary operations. Please see "5. 4 Displaying video with USB" to carry out an operation when using the USB output. 5 1 White Balance For white balance adjustment of this unit, ATW (Automatic Tracking White balance), AWB (Automatic White Balance) and MANUAL (Manual white balance) adjustments are provided. Refer to the item "7. 3 (3) WHT BAL (White Balance)", select the desired mode. Outline ATW Automatic Tracking White Balance The camera measures the object color temperature and adjusts the white balance automatically. AWB Automatic White Balance Adjust white balance by displaying the white object inside the area set by AWB menu and pressing the [DATA UP] button. MANUAL Manual White Balance Adjust the white balance manually using the WHT BAL menu while shooting the white object. The manual adjustment is most effective under shooting conditions with no color temperature variation. Adjustment is performed by confirming with a monitor. Features Tracks variations of color Measurement accuracy is temperature and adjusts white higher than ATW. mode is effective when shooting under less variations of color temperature. If illumination is low, white balance may not be corrected. Notes (1) AWB(Automatic White Balance) Set the MODE to AWB on the WHT BAL menu. Perform the C. TEMP (color temperature conversion) setting, if necessary. (Refer to the item "7. 3 (3) WHT BAL (White Balance)". ) 3200K Appropriate for indoor shooting. (Refer to the item "7. 3 (2) (2. 1) Changing gain in MANUAL mode". ) (2) OFF Gain is fixed at 0 dB. Note: White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just certain characteristics of the CMOS sensor becoming more visible. 5 3 Switching video signal output By turning on the power while the control buttons on the rear panel are pressed, the video signal output of the DVI-D terminal can be switched. When the video signal output is switched, a mode is displayed on the screen for about 5 seconds. "1080p 59. 94" Mode 1080/59. 94p 1080/50p 1080/59. 94i 1080/50i 720/59. 94p 720/50p Resolution 1920×1080/59. 94Hz (progressive) 1920×1080/50Hz (progressive) 1920×1080/59. 94Hz (interlace) 1920×1080/50Hz (interlace) 1280×720/59. 94Hz (progressive) 1280×720/50Hz (progressive) How to operate Turn on power while pressing [DISP] Turn on power while pressing [PAGE] Turn on power while pressing [MENU UP] Turn on power while pressing [MENU DOWN] Turn on power while pressing [DATA UP] Turn on power while pressing [DATA DOWN] Note: Resolution specified by the computer to which a USB cable is connected has priority while displaying/recording video from the USB terminal. Please disconnect the USB cable before switching the video signal output. 12 5 4 Display video with USB Connect a USB terminal of the camera and a USB terminal of the computer with a USB cable. Turn on the power of both the camera and the computer. * Please use a cable supporting mini-USB (B type) for the USB terminal of the camera. * To display video captured by the camera, viewer software supporting USB Video Class is required separately. * In case of Windows® XP SP2 or SP3, the built-in viewer software can be used. The procedure for using the viewer software is described below: Click Start Menu My Computer Double click USB Video Device icon, and the video will be displayed. The following can be controlled by USB from a computer. [. . . ] Instruction Manual (Owner's Manual): You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product. Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the instructions to correct the problem. Your Responsibilities This Limited Warranty is subject to the following conditions: 1. You must provide the bill of sale or proof of purchase at the time that warranty service is required. [. . . ]