User manual TOSHIBA QG30

[. . . ] User's Manual Qosmio G30 Copyright © 2006 by TOSHIBA Corporation. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Qosmio G30 Portable Personal Computer User's Manual First edition January 2006 Copyright authority for music, movies, computer programs, data bases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner. [. . . ] Standby: Data is maintained in the computer's main memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation. Refer to Chapter 5, The Keyboard, for details. Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power will be turned on in Standby Mode or Hibernation Mode but not in boot mode. If the panel power off function is enabled and you use Shut down Windows, do not close the LCD display panel until the shut down function is completed. System Auto Off This feature turns the system off automatically if it is not used for a set duration. The system shuts down in Standby mode or Hibernation mode in Windows. 6-16 User's Manual Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and other setting. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup. HW Setup window The HW Setup window contains the following tabs: General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB and Button Setting. There are also three buttons: OK, Cancel and Apply. OK Cancel Apply Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes. Accepts all your changes without closing the HW Setup window. General This window displays the BIOS version and contains two buttons: Default and About. Default About Return all HW Setup values to the factory settings. Display the HW Setup version. Setup This field displays BIOS Version and date. User's Manual 7-1 HW Setup Display This tab lets you customize your computer's display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you select the display to be used when the computer is booted - this setting is only available with standard VGA modes and cannot be configured through the Windows Desktop properties. Auto-Selected LCD + Analog RGB Selects an external monitor if one is connected. Otherwise, it selects the internal LCD (Default). Selects both the internal LCD and external monitor for simultaneous display. If the connected external monitor does not support the selected SVGA mode, selecting the LCD + Analog RGB mode will not display on that monitor. If the computer was using multiple display devices when it was last shut down and those devices are still present when Windows starts again the computer will continue to use the devices after Windows starts. If the devices are no longer present the computer will use the display specified in the BIOS "Power On Display" setting (if no external display device is connected, the computer will use the internal (attached) LCD display regardless of the BIOS "Power On Display" setting). TV Type You can select the type of TV to receive the signal. NTSC (JAPAN) PAL (S-Video) 525p (480p, D2) For Japanese television sets (Default value). This can only be selected for models with D-Video out port. 1125i (1080i, D3) This can only be selected for models with D-Video out port. 750p (720p, D4) 525i (480, D1) NTSC (US) This can only be selected for models with D-Video out port. This can only be selected for models with D-Video out port. For US television sets. When the D video output terminal is connected to the television, select either D1 through D4 in accordance to the terminal on the television. 7-2 User's Manual HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. [. . . ] SECAM L: SECAM (Sequential Color Memory) is a broadcasting standard used in France. serial communications: A communications technique that uses as few as two interconnecting wires to send bits one after another. serial interface: Refer to a type of information exchange that transmits information sequentially, one bit at a time. The electronic methodology used in serial data transmission. [. . . ]