User manual TOSHIBA RAS-10UKV-E3 SERVICE MANUAL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TOSHIBA RAS-10UKV-E3. We hope that this TOSHIBA RAS-10UKV-E3 user guide will be useful to you.

Lastmanuals help download the user guide TOSHIBA RAS-10UKV-E3.


Mode d'emploi TOSHIBA RAS-10UKV-E3
Download
Manual abstract: user guide TOSHIBA RAS-10UKV-E3SERVICE MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] SVM-04038 SERVICE MANUAL AIR-CONDITIONER SPLIT WALL TYPE RAS-10UKV -E3 / RAS-10UAV-E3 FILE NO. Safety During Installation/Servicing Refrigerant Piping Installation Tools Recharging of Refrigerant Brazing of Pipes 3. Outlined of Air Conditioner Control Description of Operation Circuit Temporary Operation Auto Restart Function Hi POWER Mode ([Hi POWER] button on the remote control is pressed. ) Filter Check Lamp Remote control 9. First Confirmation Primary Judgement Judgement by Flashing LED of Indoor Unit Self-Diagnosis by Remote Control (Check Code) Judgement of Trouble by Every Symptom Check Code 1C (Miswiring in indoor/outdoor units) and 1E How to Diagnose Trouble in Outdoor Unit How to Check Simply the Main Parts How to Simply Judge Whether Outdoor Fan Motor is Good or Bad 11. [. . . ] 9-2-12 NOTE If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall. After passing the connecting pipe through the pipe hole, connect the connecting pipe to the auxiliary pipes and wrap the facing tape around them. Do not put the drain hose end into water. Do not put the drain hose end in the drainage ditch. Fig. Put water in the drain pan and make sure that the water is drained out of doors. When connecting extension drain hose, insulate the connecting part of extension drain hose with shield pipe. Shield pipe CAUTION · Bind the auxiliary pipes (two) and connecting cable with facing tape tightly. In case of leftward piping and rear-leftward piping, bind the auxiliary pipes (two) only with facing tape. Indoor unit Auxiliary pipes Connecting cable Installation plate Drain hose Inside the room Extension drain hose Fig. 9-2-13 Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in dew-dropping. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Space for pipes Wall Drain guide · Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit. · Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. · Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) · When bending a pipe, carefully do it not to crush it. Fig. Installation Place · A place which provides the spaces around the outdoor unit as shown in the left diagram. · A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration. · A place where the operation noise and discharged air do not disturb users neighbors. · A place which is not exposed to a strong wind. · A place free of a leakage of combustible gases. · A place which does not block a passage. · When the outdoor unit is to be installed in an elevated position, be sure to secure its feet. · An allowable length of the connecting pipe is up 10m for 10UKV-E and 15m for 13UKV-E. [. . . ] Remarks Minus screwdriver Hooking claw ­ 71 ­ FILE NO. Part name Replacement of temperature sensor for servicing only Procedures Thermal sensor part Remarks Cutting here 100 1) Cut the sensor 100 mm longer than old one. 2) Cut the protective tube after pulling out it (200 mm). 3) Move the protective tube toward the Common service thermal sensor side and tear the tip of parts of sensor lead wire in two, then strip the covering TO, TS, TE, TD part. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TOSHIBA RAS-10UKV-E3

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TOSHIBA RAS-10UKV-E3 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag