User manual TOSHIBA RAS-13GAVP-E SERVICE MANUAL

[. . . ] A05-008 SERVICE MANUAL SPLIT TYPE Indoor Unit <High Wall, Heat Pump Type> Outdoor Unit <Heat Pump Type> RAS-B10GKVP-E RAS-B13GKVP-E RAS-B16GKVP-E RAS-10GAVP-E RAS-13GAVP-E RAS-16GAVP-E R410A PRINTED IN JAPAN, Nov. , 2005 ToMo CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT R410A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Improper drainage can result in water dripping inside the room. This air conditioner has been designed to drain water collected from condensation which forms on the back of the indoor unit, to the drain pan. Therefore, do not locate the power cord and other parts at a high place than the drain guide. Hook here 1 Installation plate 2 Hook Push (unhook) Fig. 10-3-19 · For detaching the indoor unit from the installation plate pull the indoor unit toward you while pushing the bottom up at the specified places. Wall Drain guide Space for pipes Push Push Fig. Installation Place · A place which provides enough space around the outdoor unit as shown in the diagram. · A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration. · A place where the operation noise and discharged air do not disturb neighbors. · A place which is not exposed to a strong wind. · A place free of combustible gases. · A place which does not block a passageway. · When the outdoor unit is to be installed in an elevated position, be sure to secure its feet. · This air conditioner accepts a connection piping length of up to 25 m. · There is no need to add refrigerant as long as the length of the connection piping is 15 m or less. · You will need to add 20 g of refrigerant per meter of added connection piping for installations requiring connection piping to be between 16 m to 25 m. · An allowable height level is up to 10 m. · A place where the drain water does not cause any problems. Precautions for adding refrigerant · Use a scale having a precision with at least 10 g per index line when adding the refrigerant. Do not use a bathroom scale or similar instrument. · Use liquid refrigerant when refilling the refrigerant. Since the refrigerant is in liquid form, it can fill quickly. Therefore, perform the filling operation carefully and insert the refrigerant gradually. CAUTION 1. Install the outdoor unit without anything blocking the discharging air. When the outdoor unit is installed in a place always exposed to strong winds like on the coast or on a high story of a building, secure the normal fan operation using a duct or a wind shield. [. . . ] Drill a hole on the side cabinet (R) for fixing the thermostat fixing plate. 2-2 PVC tube Ø9. 1 P-shape clamp Heating part Enlarged marked part Added hole 2-5 5 46 7 Ø5 hole at two positions When drilling a hole on the side cabinet (R), be sure not to damage the cabinet. 2-3 Side cabinet (R) Appendix-6 Appendix No. Photo / Explanatory diagram Side cabinet (L) Procedure Rework the side cabinet (L) to remove part of it. The area to be removed is indicated by the shaded lines in the left figure. After removing part of the side cabinet (L), deburr the edges of the side cabinet (L). 2-4 Delete Perform end process and bundling of each cable. [. . . ]